Remington EL-8: 107624-01, EL-8: 107624-02, EL-8: 107625-01, EL-8: 107625-02, EL-8: 111174-01

Page 21

CLEANING AND

MAINTENANCE

Continued

4.Hold Þle guide level. Make sure 30° mark on Þle guide is parallel to center of guide bar (see

Figure 21). This will insure that you Þle cutters at 30° angle.

5.File from inside towards outside of cutter until sharp. Only Þle in this one direction (see Figure 21). Note: Two or three strokes with Þle should sharpen cutter.

6.After each cutter is sharpened, move chain for- ward to sharpen next cutter. File all cutters on one side of chain.

7.Move to other side of chain and repeat process.

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as cut- ters are sharpened. After every second or third sharp- ening, reset cutter depth gauges.

1.Place depth gauge tool (.025") Þrmly across top of two cutters. Make sure depth gauge enters slot in depth gauge tool (see Figure 23).

2.Use medium ßat Þle. File depth gauge level with depth gauge tool.

3.Remove depth gauge tool. With ßat Þle, round off front corner of cutter depth gauge (see Fig- ure 24).

After several hand Þlings, have authorized service center or sharpening service machine sharpen chain. This will insure even Þling.

REPLACING SAW CHAIN

Replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain noted in this manual.Always include new drive sprocket when replacing chain. This will maintain proper driving of chain. Note: For proper chain and drive sprocket, see Replacement Parts and Accessories.

STORAGE

If storing saw for more than 30 days, follow steps below.

1.Drain oil tank.

2.Remove and clean guide bar and chain. Clean guide bar and chain by soaking in petroleum based solvent or mild soap and water mixture.

3.Dry guide bar and chain.

4.Place chain in container Þlled with oil. This will prevent rust.

5.Wipe a thin coating of oil over surface of guide bar.

6.Wipe off outside of saw body. Do this with soft cloth dampened with a mild soap and water mixture.

7.Store chain saw

¥in a high or locked place, out of childrenÕs reach

¥in a dry place

¥in a carrying case or with scabbard over guide bar

TECHNICAL SERVICE

You may have further questions about assembling, operating, or maintaining this saw. If so, contact DESA InternationalÕs Technical Service Department at 1-800-858-8501.

You can also visit DESA InternationalÕs technical service web site at www.desatech.com.

ILLUSTRATED PARTS LIST

See pages 46 through 50 for an Illustrated Parts Breakdown and Parts List.

REPLACEMENT PARTS AND ACCESSORIES

WARNING: Use only replacement parts and accessories described in this manual. Use of other parts or accessories could damage saw or injure operator.

See page 45 for a list of Parts Distributors near you. For a list of Authorized Service Centers near you, call 1-800-858-8501 or visit our website at www.desatech.com.

REPAIR SERVICE

Note: Only use original replacement parts. This will protect your warranty coverage for parts replaced under warranty.

Each authorized service center is independently owned and operated. For additional service center or warranty information, call 1-800-858-8501.

WARRANTY SERVICE

If saw requires warranty service, return it to nearest authorized service center. You must show proof of purchase. If faulty materials or workmanship caused damage, we will replace saw without charge.

NON-WARRANTY SERVICE

If saw requires service, return it to nearest autho- rized service center. Repairs will be billed to you at regular repair list prices. Note: Normal wear, mis- use, abuse, neglect, or accidental damage is not cov- ered under warranty.

107705

21

www.desatech.com

Image 21
Contents Listed Manual Para EL Usuario Manuel D’UTILISATION ET D’ENTRETIENBefore Operating SAW Important Safety InformationWhile Operating SAW Read ALL InstructionsKickback Safety Devices On This Saw Saw Maintenance and Kickback SafetyKickback Maintenance and Storage of Chain SAW Antes DE Utilizar LA Sierra Información Importante DE Seguridad¥ in a dry place LEA Todas LAS InstruccionesContragolpes AL Utilizar LA SierraLleve la sierra elŽctrica de un lugar a otro ¥ con el dedo fuera del gatilloMantenimiento de la cadena y seguridad contra contragolpes Mantenimiento Y Almacenamiento DE SU Sierra ELƒCTRICACuide de su sierra elŽctrica ¥ Nunca la exponga a la lluvia Avant Dõutiliser LA TRON‚ONNEUSE Consignes DE Sécurité ImportantesPendant Lutilisation DE LA TRON‚ONNEUSE ¥ lorsquon est pressŽSuite Recul Entretien de la trononneuse et protection contre le reculEntretien ET Remisage DE LA TRON‚ONNEUSE ¥ Garder vis et Žcrous bien serrŽs FIGURES/FIGURAS/FIGURESFIGURES/FIGURAS/ Figures FIGURES/FIGURAS Bucking Log When Log Is Supported On One End Guide Bar Cross Section Showing Uneven Bar Wear Unpacking Electric Chain SAWChain SAW Names and Terms Models EL-8 107624-01 107625-01, 107625-02Assembly SAW Chain Tension AdjustmentImportant Do not clamp chain saw in vise during assembly Operating Chain SAW Filling OIL TankExtension Cords Oiling ChainFelling a Tree Cutting Down a Tree Felling Procedure Felling NotchBefore Felling a Tree Felling CutLimbing a Tree Bucking a LOGTrimming a Tree Pruning Cleaning SAW Body Cleaning MaintenanceCare of Guide BAR Sharpening SAW ChainIllustrated Parts List Technical ServiceReplacement Parts and Accessories Repair Service StorageObserved Fault Possible Cause Remedy TroubleshootingIndustries of Canada, Inc Electric Chain SAW Limited WarrantyDesembalaje Sierra EléctricaTerminología EnsamblajeAjuste DE Tensión DE LA Cadena Serrada USO DE LA Sierra Eléctrica LubricaciónAntes de derribar un ‡rbol Tala DE UN çRBOL Derribamiento de un ‡rbolProcedimiento de tala Corte de la muesca Tala finalTrozado DE UN Tronco Desmembramiento DE UN çRBOLLa totalidad del tronco sobre el suelo Corte el tronco comenzando por arriba vea la FiguraTronco apoyado en un extremo Limpieza Y MantenimientoTronco apoyado sobre ambos extremos Poda DE UN çRBOLAfilado DE LA Cadena Servicio Técnico AlmacenamientoLista Ilustrada DE Partes Accesorios Y Piezas DE RepuestoServicio DE Reparaciones Servicio Durante LA GARANTêAServicio Fuera DE GARANTêA Diagnóstico Y Resolución DE Problemas Falla Observada Causa PosibleSOLUCIîN GARANTêA Limitada DE Sierra ELƒCTRICA Información DE GarantíaDéballage Tronçonneuse Électrique PrimeVocabulaire DE LA Tronçonneuse MontageRemplissage DU Réservoir D’HUILE Réglage DE LA Tension DE LA ChaîneRallonges ƒLECTRIQUES Utilisation DE LA TronçonneuseLubrification DE LA CHAëNE Systme de lubrification manuel Systme de lubrification automatiqueAvant dÕabattre un arbre Abattage Dõun ArbreProcŽdure dÕabattage Sifflet dÕabattage Trait dÕabattageTRON‚ONNAGE Dõune Bille ƑBRANCHAGEToute la bille repose au sol La bille est soutenue ˆ une extrŽmitŽTaille Dõun Arbre ƒlagage Nettoyage ET EntretienNettoyage DU Carter DE TRON‚ONNEUSE Entretien DE LA GUIDE-CHAëNERemisage Pièces DE Rechange ET Accessoires Service TechniqueListe DE Pièces Illustrées RéparationsDƒFAILLANCE OBSERVƒE DépannageCause Possible REMéDEInformation SUR LA Garantie Conserver Cette GarantieGarantie LIMITƒE Pour LA TRON‚ONNEUSE ƒLECTRIQUE Parts Company of America Replacement PARTS/PARTES DE REPUESTO/ Pièces DE RechangeMODELS/MODELOS/MODéLES 107624-01 Renvoi Parts LIST/LISTA DE REPUESTOS/LISTE DES PiècesMODELS/MODELOS/MODéLES 107625-01, 107625-02 CLAVE/N DE Parte Continœa/Ë suivre 107705 107705-01 Rev. K 02/03

EL-8: 107624-01, EL-8: 107624-02, EL-8: 107625-01, EL-8: 107625-02, EL-8: 111174-01 specifications

The Remington EL-8 is an innovative line of electric shavers that have caught the attention of grooming aficionados for their precision, technology, and user-friendly design. Within this series, the models EL-8: 107624-01, EL-8: 107624-02, EL-8: 107625-01, EL-8: 107625-02, and EL-8: 111174-01 stand out due to their unique characteristics and features that cater to diverse shaving needs.

The EL-8: 107624-01 is noted for its ergonomic design, which makes it comfortable to hold and easy to manoeuvre. It employs dual blade technology that delivers a close and seamless shave, minimizing skin irritation. This model also features a pivoting head that adapts to the contours of the face, providing an efficient shave even in hard-to-reach areas.

The EL-8: 107624-02 mirrors many of the conveniences of the 107624-01, but it introduces a built-in LED display that provides users with battery status and cleaning notifications. This added tech feature ensures that the shaver remains in peak condition, while its waterproof design allows for easy cleaning under running water, adding to the convenience factor.

Moving on to the EL-8: 107625-01, this model comes with a unique skin protector technology that reduces razor burn during shaving. It is designed with hyper-flex technology that allows for multidirectional movement of the blades, ensuring that every hair is captured in one pass. The synergistic combination of advanced blade design and patented skin protection makes this a top choice for sensitive skin types.

The EL-8: 107625-02 continues the trend by incorporating a fast-charging feature. It can fully charge in under an hour for extensive battery life, making it a reliable option for on-the-go grooming. The smart sensing capability adjusts power based on hair density, further enhancing the overall shave experience.

Lastly, the EL-8: 111174-01 introduces a luxurious touch with its sleek design and premium materials. This model emphasizes a high-performance motor that offers powerful and consistent performance, along with noise reduction technology to create a more pleasant shaving experience. It also features a convenient travel lock, making it ideal for those who travel frequently.

In summary, the Remington EL-8 series—encompassing models 107624-01, 107624-02, 107625-01, 107625-02, and 111174-01—effectively balances advanced technology with user comfort, offering a personalized grooming experience that meets the varying needs of today's modern man. With their combination of innovative features, these shavers redefine the standard for electric shaving, making each user feel confident and at ease.