Remington 104316-04,106890-01, 108526-01, 104317, 106821, 106821A Storage, Technical Service

Page 21

CLEANING AND

MAINTENANCE

Continued

4.Hold file guide level. Make sure 30° mark on file guide is parallel to center of guide bar (see Figure 19). This will insure that you file cutters at 30° angle.

5.File from inside towards outside of cutter until sharp. Only file in this one direction (see Figure 19). Note: Two or three strokes with file should sharpen cutter.

6.After each cutter is sharpened, move chain for- ward to sharpen next cutter. File all cutters on one side of chain.

7.Move to other side of chain and repeat process.

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as cutters are sharpened. After every second or third sharpen- ing, reset cutter depth gauges.

1.Place depth gauge tool (.025") firmly across top of two cutters. Make sure depth gauge enters slot in depth gauge tool (see Figure 21).

2.Use medium flat file. File depth gauge level with depth gauge tool.

3.Remove depth gauge tool. With flat file, round off front corner of cutter depth gauge (see Figure 22).

After several hand filings, have authorized service center or sharpening service machine sharpen chain. This will insure even filing.

REPLACING SAW CHAIN

Replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain noted in this manual. Always include new drive sprocket when replacing chain. This will maintain proper driving of chain. Note: For proper chain and drive sprocket, see

Replacement Parts and Accessories.

STORAGE

If storing saw for more than 30 days, follow steps below.

1.Drain oil tank.

2.Remove and clean guide bar and chain. Clean guide bar and chain by soaking in petroleum based solvent or mild soap and water mixture.

3.Dry guide bar and chain.

4.Place chain in container filled with oil. This will prevent rust.

5.Wipe a thin coating of oil over surface of guide bar.

6.Wipe off outside of saw body. Do this with soft cloth dampened with a mild soap and water mixture.

7.Store chain saw

•in a high or locked place, out of children’s reach

•in a dry place

•in a carrying case or with scabbard over guide bar

TECHNICAL SERVICE

You may have further questions about assembling, operating, or maintaining this product. If so, you can visit our Technical Service web site at www. desatech.com or contact our Technical Service Department at 1-800-858-8501 (English Only). You may also write to:

DESA Specialty Products™ P.O. Box 90004

Bowling Green, KY 42102-9004

ATTN: Technical Service Specialty Products When contacting DESA Specialty Products™, have ready

•Your Name

•Your Address

•Your Phone Number

•Model Number of Product

•Date of Purchase (Include copy of receipt for written requests).

REPLACEMENT PARTS AND ACCESSORIES

WARNING:Useonlyreplacementparts andaccessoriesdescribedinthismanual. Use of other parts or accessories could damage saw or injure operator.

For original replacement parts and accessories, con- tact your nearest Authorized Dealer or Authorized Service Center for this product. If they can not sup- ply the part or accessory, contact your nearest Parts Central listed on page 47. Each Authorized Dealer, Authorized Service Center, and Parts Central is independently owned and operated.

See pages 48 and 49 for an Illustrated Parts List.

If you need additional referral information, contact our Technical Service Department (see Technical Service). In Canada call 1-800-561-3372 for parts information. You may purchase the following service or replace- ment parts:

LNT-2

 

Part Number

Description

104302-01S#

Guide bar, 8" (20.3 cm)

104301S#

Chain, 8" (20.3 cm)

097567-01S

Guide bar, 10" (25.4 cm)

091371S

Chain, 10" (25.4 cm)

097568-02S

Guide bar, 12" (30.5 cm)

091373-02S

Chain, 12" (30.5 cm)

075752

Drive Sprocket

#Must order both pieces

Continued

108539

21

www.desatech.com

Page 20 Page 22
Image 21
Page 20 Page 22
Contents MODELS/MODELOS/MODÈLES Manual Para EL Usuario Manuel D’UTILISATION ET D’ENTRETIENBefore Operating SAW Important Safety InformationWhile Operating SAW Read ALL InstructionsSaw Maintenance and Kickback Safety Kickback Safety Devices On This SawMaintenance and Storage of Chain SAW KickbackAntes DE Utilizar LA Sierra Información Importante DE SeguridadA dry place LEA Todas LAS InstruccionesContragolpes AL Utilizar LA SierraLleve la sierra eléctrica de un lugar a otro Con el dedo fuera del gatilloMantenimiento de la cadena y seguridad contra contragolpes Mantenimiento Y Almacenamiento DE SU Sierra EléctricaCuide de su sierra eléctrica Nunca la exponga a la lluvia Avant D’UTILISER LA Tronçonneuse Consignes DE Sécurité ImportantesPendant Lutilisation DE LA Tronçonneuse Lisez Toutes LES InstructionsSuite Recul Entretien de la tronçonneuse et protection contre le reculEntretien ET Remisage DE LA Tronçonneuse ’utilisation sécuritaire et correcte de la tronçonneuse FIGURES/FIGURAS/FIGURESFIGURES/FIGURAS/ Figures FIGURES/FIGURAS Limbing a Tree Guide Bar Cross Section Showing Uneven Bar Wear Unpacking Electric Chain SAWChain SAW Names and Terms Remove all items from cartonAssembly SAW Chain Tension AdjustmentImportant Do not clamp chain saw in vise during assembly Operating Chain SAW Filling OIL TankExtension Cords Oiling ChainFelling a Tree Cutting Down a Tree Felling Procedure Felling NotchBefore Felling a Tree Felling CutLimbing a Tree Bucking a LOGTrimming a Tree Pruning Cleaning SAW Body Cleaning MaintenanceCare of Guide BAR Sharpening SAW ChainReplacement Parts and Accessories Technical ServiceStorage Filing Cutter Depth GaugesWarranty Service Repair ServiceNON-WARRANTY Service GeneralObserved Fault Possible Cause Remedy TroubleshootingElectric Chain SAW Limited Warranty Model Date PurchasedIndustries of Canada, Inc Desembalaje Sierra EléctricaTerminología EnsamblajeAjuste DE Tensión DE LA Cadena Serrada USO DE LA Sierra Eléctrica LubricaciónCables DE Prolongación Lubricación DE LA CadenaAntes de derribar un árbol Tala DE UN Árbol Derribamiento de un árbolProcedimiento de tala Corte de la muesca Tala finalTrozado DE UN Tronco Desmembramiento DE UN ÁrbolLa totalidad del tronco sobre el suelo Siga estas instrucciones para trozar un troncoTronco apoyado en un extremo Limpieza Y MantenimientoTronco apoyado sobre ambos extremos Poda DE UN ÁrbolAfilado DE LA Cadena Cuidado DE LA Barra DE GuíaServicio Técnico AlmacenamientoAccesorios Y Piezas DE Repuesto Recambio DE LA Cadena SerradaAccesorios Y Piezas Servicio DE DE Repuesto Reparación Servicio CON GarantíaServicio SIN Garantía Falla Observada Causa Posible Solución Diagnóstico Y Resolución DE ProblemasModelo Fecha de compra Garantía Limitada DE Sierra EléctricaDéballage Tronçonneuse Électrique PrimeVocabulaire DE LA Tronçonneuse MontageRéglage DE LA Tension DE LA Chaîne Remplissage DU Réservoir D’HUILEÉtendez la chaîne, bien à plat Rallonges Électriques Utilisation DE LA TronçonneuseLubrification DE LA Chaîne Sciage Avec LA TronçonneuseAvant d’abattre un arbre Abattage D’UN ArbreProcédure d’abattage Sifflet d’abattage Trait d’abattageTronçonnage D’UNE Bille ÉbranchageToute la bille repose au sol La bille est soutenue à une extrémitéTaille D’UN Arbre Élagage Nettoyage ET EntretienNettoyage DU Carter DE Tronçonneuse Entretien DE LA GUIDE-CHAÎNERemplacement DE LA Chaîne RemisageAffûtage DE LA Chaîne Pièces DE Rechange ET Accessoires Service TechniqueNuméro De pièce Description 104301S Chaîne, 20,3 cm 8 po 075752 Pignon d’entraînementService DE Réparation Service Sous GarantieService Hors Garantie Défaillance Observée Cause Possible Remède DépannageInformation SUR LA Garantie Garantie Limitée Pour LA Tronçonneuse ÉlectriqueModèle Date dachat Parts CENTRAL/CENTRAL DE PIEZAS/DÉPÔT DE Pièces LNT-2 NPC-4C Parts LIST/LISTA DE REPUESTOS/LISTE DES Pièces108539 108539 108539-01 Rev. H 04/05
Top Page Image Contents