Quadra-Fire SAPPH-D-CWL Grille Cover Plate Installation, Accessories, 059 53 DMS 096 41DMS

Page 31

Figure 8.9 Remove burner by sliding the shutter to the right, lifting up the left side of the burner and sliding it the the left.

Figure 8.10 Remove the main burner orifice using a 5/8 in. wrench.

Replace the orifice with the proper size as indicated for your gas type.

PROPANE

NATURAL GAS

.059 (53 DMS)

.096 (41(DMS)

NOTE: If the venting configuration has no vertical rise, a derating orifice must be installed. The derating orifices are supplied with the rear vent conversion kit.

Reinstall the burner. Slide the burner neck into the shutter and over the orifice. Refer to Figure 8.10.

Reinstall the burner pan locators on the left and right side of the burner. Secure with one screw to each side.

Install logs, referring to instructions on page 33.

Replace glass door and front.

C. Grille Cover Plate Installation

Top grill cover is shipped with the appliance and is an optional use item. It may be used with rear or top venting. Primarily its purpose is to hide the interior of the top of the appliance from being viewed through the top grill piece. Its use will also increase the efficiency of the blower, if a blower is installed on the appliance.

To prepare the part for use you will need tin snips, pliers and a hammer.

1, For use with top venting: See Figure 8.11, below. Use the tin snips to cut the straight edges.

2.Gently bend the piece until the two attached sections of the circular area snap apart. Discard this piece.

3.Bend the tabs up towards the black painted side.

4.With the top grill lying face down, set the black painted side of grill cover onto the grill.

5.Use the hammer to tap on the four speed nuts (also supplied with the appliance.)

6.For use with rear venting: Follow steps 3 through 5, leaving the cover piece intact.

SNIP HERE

BEND 7 TABS

TOWARDS

PAINTED SIDE

Figure 8.11

D. Accessories

Install approved accessories per instructions included with accessories. Refer to Section 12 for appropriate accesso- ries.

WARNING

Shock or fire risk.

Use ONLY optional accessories approved for this appliance.

Using non-listed accessories voids warranty.

Using non-listed accessories may result in a safety hazard.

Only Hearth & Home Technologies approved accessories may be used safely.

January 28, 2008

Quadra-Fire · Sapphire · 250-7233E

Page 31

Image 31
Contents Do not Discard this Manual What to do if you smell gasSolitaire Front Quartet FrontQuadra-Fire · Sapphire · 250-7233F January 28 Table of Contents 1Listing and Code Approvals BELOW. Keep Clear of ALL Obstructions Requirements for the Commonwealth of MassachusettsManufacturer Requirements Tools and Supplies Needed Getting StartedSelecting Appliance Location Appliance Location and ClearancesClearances Vent Termination Minimum Clearances 4Termination LocationsAlcove Applications Measuring Standards Vent InformationVenting Components Use of ElbowsTOP Vent Graph Rear Venting with Vertical Rise How to Use the Vent Graph Venting GuidelinesStep Type B Rear Installations for Use with Rear Vent KitType a Up & Out Installations for Top Vent Configurations Horizontal TerminationElbow in Corner Installation 203mm 178mm 152mm Direct Vent Pipe Vertical TerminationStep Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Ft m Existing Masonry ChimneyCap Flex Liner Flex Coupler Sheet Metal Screws Fuel Conversions Gas InformationConverting to LP Gas Propane Natural GAS Pressure Gas PressuresCheck for GAS Leaks Gas ConnectionWire Size Max. Length Recommendation for WireConnecting to the Appliance Standing Pilot Ignition System WiringThermopile GAS Pilot Ignitor Thermocouple At the TOP of the appliance, with exceptions noted Appliance SetupRemove Shipping Materials Top and Rear Vent ConversionReplace Burner Orifice for Horizontal Vent Configurations Accessories Grille Cover Plate Installation059 53 DMS 096 41DMS Quartet Door Alignment Front InstallationFronts are shipped attached to the face For Both Quartet and Solitaire FrontsPositioning the Logs Hearth Legs InstallationQty Description Blower from front Glass Door Assembly InstallationBlower Installation Mineral WoolPage Blower 26 Blower Wiring DiagramMake adjustment Damper AdjustmentShutter Adjustment For TOP or Rear Vent InstallationsBefore Lighting Appliance Operating InstructionsControls Lighting Appliance For Your Safety Read Before LightingInitial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Symptom Possible Cause Corrective Action TroubleshootingBe Placed in this Opening After servicing Maintaining and Servicing ApplianceNecessary. USE Caution When CLEANING/HANDLING Ceramic Burner Maintenance Tasks InspectDate of Service Performed By Description of Service Service and Maintenance LogReference Materials Appliance Dimension DiagramVent Components Diagram Miscellaneous Vent Components ListItem # Description RD. Service Parts ListRD. Service Parts cont’d Service Parts cont’d Cast Parts Individual Pieces AccessoriesWarranty Policy This page Intentionally Left Blank January 28 Quadra-Fire · Sapphire · 250-7233E Contact Information SapphireDealer Telephone