Makita DCS 9000 manual Startingthe engine, Checking the chain brake, Switching off the engine @

Page 9

Startingthe engine

I

-Move at least 3m awayfrom the place where you fuelled the saw.

-Ensure to have a safe footing and put the chain saw on the floor such that the sawing device is con in contact with any object.

-Actuating the chain brake (blocking).

-Put the short-circuiting switch in position "I"(START) (B/I).

-Hold the tubular handle tightly with one hand and press the chain saw to the ground.

-Put your tip-toe in the back hand guard.

When working with a model equipped with a decompress- ion valve observe the following:

-Press switch (B/6) before starting the engine.

-The valve will close automatically after ignition has taken place.

Checking the chain brake

Do not work with the chain saw without first checking the chain brake!

-Start the engine as described (make sure you have a good footing, and place the chain saw on the ground in such a way that the guide bar is free of contact).

-Grasp the tubular handle firmly with one hand and hold the grip with the other.

-With the engine running at moderate speed, press the hand guard (C/6)in the direction of the arrow with the back of y w hand until the chain brake engages. The chain should stop immediately.

-Immediately release the throttle and release the chain brake.

IMPORTANT: If the chain does not stop immediately when you test the chain brake, do NOT use the chain saw. Take the chain saw to a MAKITA service center.

-2

-3

Cold start:

-Pull the choke (B/2).

-Press the safety switch (B/3).

-Pressthe throttle lever (B/4)and lock it with the stop button(BE).

-Slowly pull out the starter cable until you notice a resistance (the piston is positioned before the top dead centre).

-Now pull out the starter cable with a fast and forceful movement until you hear a first ignition.

Attention: Do not pull out the startercable morethan approx. 50 cm and lead it back by hand.

-Press the choke (B/2) and again pull the starter cable. As soon as the engine will run, touch the throttle lever (B/4) to disengage the stop button (BE).

Attention: As soon as the engine is started it must run without any load to prevent the chain brake from being

-Now release the chain brake. 8 @Jdamaged.

Warm start:

-As described in the section above (cold start), but without actuating the choke (B/2).

Switching off the engine @

-

Put the short-circuitingswitch (B/1) in position "0"(STOP).

Checking the chain lubrication

Never work with the chain saw when a sufficient chain lubrica- tion is not guaranteed. Otherwise the service life of the sawing device will be reduced.

Before starting work check the oil level in the tank and the oil feeding.

Check the oil feed quantity as described below:

-Start the chain saw.

-Hold the running chain saw approx. 15 cm above a trunk or the ground (use an appropriate base).

If the lubrication is sufficient,you will see a light oil trace because oil will be centrifuged from the sawing device.

14

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Pagina 71-73,78 Table of contents Thank you for purchasing a Makita productPacking Delivery SymbolsGeneral precautions Safety PrecautionsDCS Denaimination of componentsChain brake Fuel Fuels / RefuellingFuel mixture Correct mixture ratioAdjusting the chain lubrication Follow the Safety PrecautionsMotor must be switched off Avoid Skin and EYE ContactStartingthe engine Switching off the engine @Checking the chain brake Checking the chain lubricationDCS Herzlichen Dank fur Ihr Vertrauen LnhaltsverzeichnisVerpackung Lieferumfang SymboleHinweis SICHERHElTSHlNWElSEZundkerze ZundanlageElektrodenabstand Oder Zundkerze 11300 200Kettenbremse auslosen blockieren KettenbremseNiemals Altol Verwenden Betriebsstoffe / Tanken @ @Kraftstoff50l 40l Herstellung des richtigen MischungsverhaltnissesTanken HAUT- UND Augenkontakt VermeidenUNBEDINGTSlCHERHElTSHlNWElSEBEACHTEN KettenschmierungeinstellenKettenbremse prufen Motor startenMotor ausschalten Kettenschmierung prufenAuszug aus der Ersatzteilliste Nous vous remercions de votre confiance Declarationde conformite pour la CEESommaire Etendu Symboles’hesitez pas a consulter votre revendeur Dolmar RemarqueDesignation des pieces Caracteristiques techniquesQue la chaine s’applique sur la face inferieure du rail Frein de chaTneContrBle de la tension de la chaine Continuer a relever la pointe du rail-guide de la chaine etHuile de chaine de sciage Melange carburantRemarque ’UTILISEZ Jamais DE Huiles UsageesEvitez LE Contact Avec LA Peau ET LES Yeux Respecter Imperativementles Regles DE SecuriteReglage du graissage de la chaine Verifier le frein de chaTne Demarrer le moteurArrQterle moteur Verifier le graissage de la chaineExtrait de la liste des pieces de rechange Lndice Muchas gracias para su confianzaEnvase Aplicacion en inviernoSimbolos Extension del suministroMotosierra Makita DCS Guia Cadena Protector del riel Herramienta de montajeRecomendaciones generales Recomendaciones DE SeguridadCaracteristicas de una sierra accionada por motor NotaDenominacion de 10s componentes 3\ Datos tecnicosEn la fraccion de un segundo la cadena para Freno de cadenaPoner en funcion el freno de cadena bloquear Soltar el freno de cadenaCargar combustible Mezcla de combustibleLceite para cadenas Tomar combustible Ajustar el engrase de cadenaLubrificar la cadena de sierra Is610 si el motor esta desconectado! @Controlar el freno de cadena Arrancar el motorParar el motor Controlar el engrase de cadenaEtracto de la lista de piezas de repuesto Inhoudsopgave Werkplaatsservice,reserve-onderdelenenVerpakking Type SerienummersOmvar SymbolenOpmerking VeiligheidsvoorschriftenBenaming van de onderdelen Technische specificatiesGashendel Tankdop brandstoftankControle van de kettingspanning 0STOP KettingremEen fractie van een seconde wordt de zaagketting stilgezet Kettingrem inschakelen blokkerenBradstof Gebruik Nooit Afgewerkte OLlELiter BrandstofmengselKettingsmering afstellen HUID- EN OogcontactvermijdenMotor uitzetten Kettingrem controlerenKetti ngsmering controleren Warme startVerantwoordelijk Uittreksel uit de reserve-onderdelenlijstMolte grazie per la fiducia nei nostri confronti Simboli Parti integranti della fornituraCenni generali Cenni Sulla Sicurezza291 430 50l Denominazione dei singoti pezzi DCSG n yTarghetta DCS 9000 Indicate i dati quando ordinate pezzi di ricambioLa catena della sega si arresta in una frazione di secondo Controllo della tensione della catenaAzionamento del freno della catena bloccaggio Allentamento del freno della catenaMateriali d’esercizio RifornimentoCarburante MiscelaRegolazione della lubrificazione di catena Rifornimento di carburanteLubrificazione della catena della sega Disinserite prima sempre il motoreControllate la freno della catena Avviamento del motoreSpegnimento del motore Controllate la lubrificazione della catenaEstratto dalla lista dei pezzi di ricambio

DCS 9000 specifications

The Makita DCS 9000 is a powerful and versatile chainsaw designed for demanding applications in professional forestry, construction, and landscaping. Known for its reliability and performance, the DCS 9000 is primarily aimed at professionals who require a robust tool to tackle heavy-duty cutting tasks.

One of the standout features of the Makita DCS 9000 is its high-performance engine. Equipped with a 90cc, 2-stroke engine, this chainsaw delivers an impressive power-to-weight ratio, enabling it to handle large-diameter logs and thick branches with ease. The advanced engine technology also contributes to improved fuel efficiency and reduced emissions, aligning with the increasing environmental standards in the industry.

The DCS 9000 incorporates a sophisticated air filtration system that helps to extend the life of the engine by keeping dust and debris at bay. This system ensures that the chainsaw operates efficiently, even in challenging environments, providing a longer service life for the tool. Furthermore, the quick-access air filter cover allows users to easily maintain the filter, keeping the chainsaw in optimal working condition.

In terms of safety features, the DCS 9000 is equipped with a chain brake that prevents accidental activation and protects the user from injury. The tool's anti-vibration technology effectively reduces hand fatigue during prolonged usage, enhancing comfort and control. Additionally, the chainsaw features a built-in inertia brake that stops the chain swiftly when necessary, ensuring safer operation.

The ergonomic design of the DCS 9000 includes a lightweight construction that balances power and ease of use, enabling operators to maneuver the tool with precision. The soft-grip handles provide added comfort, allowing for extended periods of operation without discomfort.

Another notable characteristic of the DCS 9000 is its heavy-duty bar and chain, which are engineered for longevity and optimal cutting performance. The tool can accommodate various bar lengths, making it adaptable for different cutting tasks.

Overall, the Makita DCS 9000 stands out as a premium chainsaw made for professionals. Its combination of power, safety features, and ergonomic design ensures that users can tackle tough jobs with confidence and efficiency. Whether felling trees, pruning branches, or cutting firewood, the DCS 9000 is a reliable companion for any cutting task.
Top Page Image Contents