Briggs & Stratton 1679-0 Power During Fault Condition, Low Voltage, Engine Fail To Start

Page 17

Briggs & Stratton Power Products Home Generator System

Owners Manual

Low Voltage

This fault is indicated by three blinks.This condition is caused by a restriction in the fuel flow, a broken or disconnected signal lead, a failed alternator winding, the control panel circuit breaker is open, or overloaded circuits in the transfer switch.

Remedy the problem (you may need to contact your installer or Briggs and Stratton Technical Services for assistance), then reset the Fault Detection system, as described above.

Engine Fail To Start

This fault is indicated by four blinks.This feature prevents the generator from damaging itself if it continually attempts to start in spite of another problem, such as no fuel supply. Each time the system is directed to start, the unit will crank for 15 seconds, pause for 15 seconds, crank for

15 seconds, pause for 15 seconds, and repeat. If the system does not begin producing electricity after approximately 90 seconds, the unit will stop cranking and the LED will blink.

The most likely cause of this problem is no fuel supply. Check the inside and outside fuel shut off valves to ensure they are fully open. Other causes could be failed spark plug(s), failed engine ignition, or the engine air filter is clogged.You may need to contact your installer for assistance if you can’t remedy these problems.When the problem is corrected, reset the Fault Detection system as described above.

Low Frequency

Engine Overspeed

This fault is indicated by 6 blinks.This feature protects devices connected to the transfer switch by shutting the generator down if its engine happens to run faster than the preset limit.The overspeed fault is detected as follows:

If the generator output frequency runs at 72 Hz for five seconds, the generator will shut down.

If the generator output frequency reaches 75 Hz, the generator will shut down instantly.

This condition is caused by a failed engine governor.To remedy the problem, you should contact your installer or Briggs and Stratton Technical Services for assistance.When the problem is corrected, reset the Fault Detection system as described above.

Oil Temperature High

This fault is indicated by seven blinks.The contacts of the temperature switch (Figure 5) are normally open. If the engine temperature exceeds approximately 140°C (284°F), the fault is detected and the engine shuts down.

Common causes for this condition include running the unit with all access doors removed, obstructed air inlet or exhaust port, or debris in the engine cylinder cooling fins. To resolve the problem, remove any accumulated debris and obstructions and let the engine cool down. Ensure that the Oil Service door and/or the Control Panel door is installed whenever the unit is running.When the problem is corrected, reset the Fault Detection system as described above.

This fault is indicated by 5 blinks.This feature protects devices connected to the transfer switch by shutting the generator down if its engine runs slower than the preset limit.

This condition is caused by a failed engine governor or by excessive loads on the transfer switch.To remedy the problem, you may need to contact your installer or Briggs and Stratton Technical Services for assistance.When the problem is corrected, reset the Fault Detection system as described above.

Power During Fault Condition

Whenever the Home Generator System is in an uncorrected fault condition, the automatic transfer switch is reset to UTILITY POWER.This means that when utility power is restored, utility power will be applied to the essential circuit loads.The generator is disconnected from the automatic transfer switch for the duration of any detected fault condition.

17

Image 17
Contents Call Home Standby Helpline Manual del Propietario Manuel de lUtilisateurTable of Contents Safety Rules Briggs & Stratton Power Products Home Generator System Introduction Installation AssistanceOwner Orientation For the Home or Business OwnerGenerator Location Power Decrease at High Altitude or High TemperatureFuel Factors Generator ClearancesEssential Circuits Typical Completed Automatic Transfer Switch InstallationEssential Circuit Selection Device Running WattsDelivery Inspection Shipment ContentsUnpacking Know Your Backup Generator LED Know Your System Control PanelTo Install an Access Door Access DoorsTo Remove an Access Door AUTO/OFF/MANUAL Switch Battery ConnectionBefore Initial START-UP Engine OilAutomatic Operation Setting Exercise TimerChecking Automatic Operation Stopping the SystemTransfer Switch SpecificationsTo perform the Set Exercise procedure GeneratorFault Detection System MaintenanceOil Temperature High Power During Fault ConditionLow Voltage Engine Fail To StartGenerator To Clean the GeneratorStorage Changing Engine OilTroubleshooting Briggs & Stratton Power Products Home Generator System Briggs & Stratton Power Products Home Generator System Unit Schematic Diagram Unit Wiring Diagram Transfer Switch Schematic Diagram Transfer Switch Wiring Diagram Unit Exploded View Qty. Description Unit Parts ListEnclosure Exploded View Part Not Illustrated Enclosure Parts ListInsulation SET Exploded View Insulation SET Parts List Alternator Exploded View and Parts List Resistor Control Panel Exploded View and Parts ListTransfer Switch Exploded View Transfer Switch Parts List Manual del Propietario Tabla DE ContenidoPeligro Instrucciones DE SeguridadAdvertencia Precaución Orientación Para EL Propietario IntroducciónAsistencia para la instalación La instalación de los Sistemas de GeneradoresDistancias Desde el Generador Factores Relacionados con el CombustibleUbicación del Generador Selección de los Circuitos Fundamentales Circuitos FundamentalesTostadora Dispositivo Vatiaje deInspección al Momento de la Entrega DesempaqueContenido de la Caja El Sistema de Generador Doméstico incluye lo siguienteConozca SU Generador Doméstico Conozca EL Panel DE Control DEL Sistema Para Instalar una Puerta de Acceso Puertas de AccesoPara Retirar una Puerta de Acceso Aceite de Motor Antes DEL Arranque InicialSistema de Combustible Gaseoso Interruptor AUTO/OFF/MANUAL automático/apagado/manualOperación Automática Configuración del Temporizador de PrácticaVerificación de la Operación Automática Paro del SistemaConmutador de Transferencia EspecificacionesGenerador Sistema de Detección de Fallas MantenimientoEnergía Durante una Condición de Falla Almacenamiento Mantenimiento DEL GeneradorCambio del Aceite del Motor Para Limpiar el GeneradorReparacion DE Averias Manuel dUtilisation Table DES MatièresAvertissement Règles DE SécuritéLe contact de ces pièces risque de causer de graves brûlures Introduction Aide à lInstallationConseils AU Propriétaire Au Propriétaire Résidentiel ou CommercialDégagement Autour de la Génératrice Emplacement de la GénératriceFacteurs Relatifs au Combustible Circuits Essentiels Fils dalimentation Fils de signalSélection des Circuits Essentiels Appareil WattsVérification de la Livraison DéballageContenu de la Boîte Le Groupe Électrogène est Livré avec les Éléments SuivantsBatterie La position normale de fonctionnement est la position Pour Enlever une Porte dAccès Pour Installer une Porte dAccèsPortes dAccès Huile à Moteur Avant LE Démarrage InitialBranchement de la Batterie Système de Combustible GazeuxVérification du Fonctionnement Automatique Fonctionnement AutomatiqueArrêt du Système Réglage de la Minuterie du Cycle dExerciceGénératrice CaractéristiquesCommutateur de Transfert Pour Exécuter la Procédure de Réglage du Cycle dExerciceSystème de Détection des Pannes EntretienAlimentation en Situation de Panne Remisage Entretien DU GénérateurVidange de lHuile Moteur Pour Nettoyer le GénérateurDépannage Remarques