Baldor TS80, TS25 Trailer Light KIT Wiring Instructions, Trailer Light Mounting and Connection

Page 51

TRAILER LIGHT KIT

WIRING INSTRUCTIONS

Connect the wires of the short trunk connector to the vehicle wiring. Connect the brown wire to the tail light wire, the yellow wire to the left–hand stop and turn, and the green wire to the right–hand stop and turn wire. Attach the white ground wire to the vehicle frame. If vehicle has rear turn signals separated from stoplights, you will need an Anderson 5403 electronic converter.

TRAILER LIGHT MOUNTING AND CONNECTION

Mount the light with license window on the left rear of the trailer with side marker to the outside of the trailer. Mount the light without license window on the right rear of the trailer with side marker to the outside. Mount the license bracket with the left–hand light.

Using frame clips, mount each half of the harness down each side of the trailer, with yellow and brown wires down left side and green and brown wires down right side. Connect yellow and brown wires to left side and green and brown wires down right side. Connect yellow and brown wires to left–hand light by stripping harness ends $” and inserting yellow wire into hole marked “Stop and Turn (yellow)”. Insert brown wire into hole marked “Tail (brown)”. (Extra holes are spares for auxiliary use.) Connect green and brown harness ends to the right–hand light in the same manner. Attach white ground wire to trailer tongue or frame.

Mount the front side marker lights in the area shown. Attach wire to brown harness wire with 3M Scotchlok connector. (Kits 540,545, 547).

Mount the three red marker lights to rear of trailer making sure that the lamps are no less than 6” and no more than 12” from center of lamp to center of lamp. (Kit 547)

After lamps are mounted, use 3M Scotchlok connectors to connect all three leads together and then plug into the extra hole marked brown in the back of taillight (either side).

NOTE: Smaller holes above or below circuit holes on all lights are relief holes to be used for removal of wires. By inserting nail or paper–clip into these small holes the strain on the wires can be relieved so they can be moved.

Connect harness plug to trunk connector plug. Turn on car headlights – both tail and all four side markers should come on. The brighter stoplights should come on only when the brake pedal is depressed, or when turn signal is activated, (Key must be in “on” position.) If lights do not light, check all ground connections. If turn signals do not operate properly, check connections between vehicle wiring and trunk connector.

NOTE: All lights used in these kits comply with D.O.T. standards. Some kits do not contain all of the lights needed to meet vehicle requirements.

26

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Baldor Generators OPERATOR’S Manual TowablesPage Safety Warnings FORM# S-PSG-001-3 ```` for Gasoline or Diesel Powered Generator Sets ```` Page Forward \ISO9001\FORMS\SCSD0037.MSW Features & Specifications Page Switchable Connection Information Control Panel Operation Function Page Page Operation PRE-START Procedure Operation Starting Operation Cranking Control LOW Voltage Troubleshooting GeneratorFluctuating Voltage High VoltageOverheating Mechanical Noise Generator Frame Produces Shock When TouchedTroubleshooting Engine Page Magnaplus Generator Table of Contents Specifications Parts List Single Bearing Storage SafetyReceiving and Storage Unpacking and HandlingPMG optional Principles of OperationPreparation for USE InstallationParallel Operation Nonlinear LoadingEND Play Testing Generator MountingTorsional Vibration Environmental Considerations Wiring ConnectionsLOW WYE Connection Double Delta -- Single Phase Connection Operation PRE-START InspectionSTART-UP Shutdown Procedure MaintenanceDrying Windings TestingField Flashing ServiceDiode Testing GeneralBearing Removal Bearing ReplacementReturned Goods TroubleshootingGenerator Produces LOW VOLTAGE, no Load Generator Produces no VoltageGenerator Produces LOW Voltage When Load Applied Generator Produces Fluctuating VoltageGenerator Produces High Voltage Generator Produces Mechanical Noise Generator is OverheatingSpecifications Parts List Single Bearing Parts List Dual Bearing Towing Vehicle Rules for Safe Trailer OperationTowing Heavy Trailer Loads Electrical Trailer WiringSafety Checks Trailer Light Mounting and Connection Trailer Light KIT Wiring InstructionsLimited Warranty Owner’s Responsibilities Page California Proposition 65 Warning
Related manuals
Manual 88 pages 1.48 Kb
Top Page Image Contents