Boston Acoustics CPS 10Wi, CPS 8Wi, CPS 12Wi Optional WT 50 Wireless Transmitter, Operation

Page 7

Optional WT 50 Wireless Transmitter

Transmitter Power

Plug the transmitter power supply into a power outlet. The transmitter power supply requires very little power so you can plug it into an auxiliary power outlet on the receiver. Plug the connector on the power supply cable into the transmitter power input labeled 18V DC.

Wireless ID Switches

Both the CPS Wi Subwoofer and optional WT 50 Wireless Transmitter have Wireless ID switches (located on the rear of the subwoofer and transmitter). The various switch settings change the digital identification code of the wireless signal the WT 50 sends to the subwoofer. The two switches must be set to the same position. Typically you’ll never need to adjust these switches. They are included in case you have more than one CPS Wi subwoofer in your house. Use different Wireless ID switch settings so the subwoofers won’t interfere with each other.

4 3 2 1

L R LFE

DC 18V

 

 

 

 

WT 50 Transmitter

 

 

 

Receiver

 

 

 

 

 

 

 

 

 

 

 

 

 

Power supply cord

Note: Do not connect the same audio source to the subwoofer and WT 50 wireless transmitter at the same time.

Operation

Audio On/Auto/Mute

Plug the subwoofer’s AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Set the audio switch to the desired setting.

AUDIO ON – The subwoofer audio is always on.

AUTO – The subwoofer audio will turn on whenever a signal is detected. If no signal is detected after several minutes, it will automatically enter the Mute mode.

MUTE – The subwoofer is muted and will not produce any sound. You may want to unplug your subwoofer if you will not be using it for some time or wish to conserve electricity. (On 230v models only, you may turn off the main power switch, located next to the power cord)

An LED indicator next to the Polarity switch indicates what mode the subwoofer is in: OFF – The subwoofer is unplugged (or the main power switch is off on 230v models) RED – Mute (No signal detected, Amp Off )

gREEN – Audio On (Signal detected, Amp On)

The subwoofer will automatically enter the Mute mode after several minutes when no signal is detected from your system. The subwoofer audio will then turn ON instantly when a signal is detected.

Polarity Control

(0° or 180°): Selects regular (0°) or inverted (180°) phase for the subwoofer. Set this switch to provide the fullest, most dynamic bass. The effect of phase will be most audible on low-frequency percussion instruments or music with a continuously repeating bass line.

Crossover Control

Adjusts the frequency of the low pass filter for the subwoofer. Note: This control is not active when using the LFE input jack.

Volume Control

Turn the subwoofer Volume control to the 11 o’clock position. If no sound emanates from the subwoofer, check the AC-line cord, Audio On switch, Power switch (on 230v models), and input cables.

Adjust the subwoofer Volume control until you hear a match between the main speaker and subwoofer. Bass response should not overpower the room but rather be adjusted so there is a natural blend across the entire musical range.

7

Image 7
Contents Classic Canadian Users American UsersIntroduction SpecificationsFeatures Boston Acoustics Classic Series Wireless-Ready SubwoofersUnpacking the System Placement OptionsConnections Connecting the Subwoofer to Stereo or Dolby Pro LogicAdjusting the Crossover Control Connecting to Electronics Without a Subwoofer OutputSpeaker level Operation Optional WT 50 Wireless TransmitterFor EU Customers Only Maintenance and ServiceLimited Warranty If Service Seems NecessaryUsuarios de los Estados Unidos Instrucciones DE SEgURIDAD ImportantesUsuarios de Canadá Subwoofers Boston Acoustics inalámbricos Serie Classic EspecificacionesIntroducción CaracterísticasOpciones de colocación Desembalaje del sistemaConexión del subwoofer a estéreo o Dolby Pro Logic ConexionesNota Conexión al sistema electrónico sin una salida de subwooferAjuste del control de frecuencia de cruce Nivel del parlanteAudio On Encendido /Auto Automático / Mudo En espera Control de volumenFuncionamiento Interruptores ID inalámbricosControl de polaridad Mantenimiento y ServicioGarantía Limitada Si cree que necesita asistencia técnicaUtilisateurs canadiens Utilisateurs américainsCaractéristiques SpécificationsOptions de positionnement Désemballage du systèmeConnexions Arrière du Réglage de la commande du Répartiteur CrossoverConnexion à l’électronique sans sortie de caisson de graves Niveau du haut-parleurCommutateurs ID sans fil Commande du répartiteurContrôle du volume FonctionnementContrôle de la polarité Entretien et serviceGarantie limitée ’il semble nécessaire d’effectuer une révisionUtilizzatori canadesi Utilizzatori americaniCaratteristiche Subwoofer Wireless-Ready Classic Series di Boston AcousticsSpecifiche IntroduzioneOpzioni di collocazione Disimballaggio del sistemaConnessioni Oppure Nota Connessione ad elettronica priva di un’uscita subwooferRegolazione del comando Crossover Livello di altoparlanteFunzionamento Trasmettitore WT 50 Wireless opzionaleClienti UE Manutenzione e serviziGaranzia limitata Caso di necessità di assistenzaKanadensiska användare Användare i USAInledning SpecifikationerFunktioner Placeringsalternativ Packa upp systemetAnslutningar Ansluta subwoofern till digitala hemmabiosystem med LFEAnsluta subwoofern till stereo eller Dolby Pro Logic Justera övergångskontrollen Ansluta till elektroniken utan subwooferutgångHögtalarnivå Drift Valfri WT 50 trådlös sändareEndast för kunder inom EU Underhåll och serviceOm service verkar behövas Begränsad garantiAmerikanische Verbraucher WICHTIgE SICHERHEITSANWEISUNgENKanadische Verbraucher Einführung SpezifikationenAusstattung Aufstellungsoptionen Auspacken des SystemsAnschlüsse Lautsprecherpegel Einstellung des Crossover-ReglersOder Hinweis Betrieb Optionaler Wireless Transmitter WTNur für Kunden in der EU Wartung und KundendienstEingeschränkte Garantie ReparaturanforderungJubilee Drive, Peabody, MA 01960 USA