Craftsman 247.88833 manual Safety Instructions, California Proposition, Training, Preparation

Page 3

SAFETY INSTRUCTIONS

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol, HEED ITS WARNING!

DANGER

This machine was built to be operated according to the safe opera- tion practices in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating fingers, hands, toes and feet and throwing debris. Failure to observe the following safety instructions could result in serious injury or death.

WARNING

California Proposition 65

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

WARNING

Your Responsibility—Restrict the use of this power machine to persons who read, understand and follow the warnings and instruc- tions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

Training

Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.

Never allow children under 14 years of age to operate this machine. Children 14 and over should read and understand the instructions and safe operation practices in this manual and on the machine and be trained and supervised by an adult.

Never allow adults to operate this machine without proper instruction.

Thrown objects can cause serious personal injury. Plan your snow-throwing pattern to avoid discharge of material toward roads, bystanders and the like.

Keep bystanders, pets and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

Exercise caution to avoid slipping or falling, especially when operating in reverse.

Preparation

Thoroughly inspect the area where the equipment is to be used. Remove all doormats, newspapers, sleds, boards, wires and other foreign objects, which could be tripped over or thrown by the auger/ impeller.

Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes.

Do not operate without wearing adequate winter outer garments. Do not wear jewelry, long scarves or other loose clothing, which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

Use a grounded three-wire extension cord and receptacle for all machines with electric start engines.

Adjust collector housing height to clear gravel or crushed rock surfaces.

Disengage all control levers before starting the engine.

Never attempt to make any adjustments while engine is running, except where specifically recommended in the operator’s manual.

Let engine and machine adjust to outdoor temperature before starting to clear snow.

3

Image 3
Contents 30/2008 Form noTable of Contents Warranty StatementProduct Specifications Model Number Preparation Safety InstructionsCalifornia Proposition TrainingSafe Handling of Gasoline OperationMaintenance & Storage Do not modify engineSpark Arrestor Symbol Safety SymbolsUSE CLEAN-OUT Tool to Unclog Discharge Chute Safety LabelsPlace the shift lever in the F6 position AssemblyAssembly Removing From CrateChute Clean-Out Tool Set-UpDrift Cutters Retighten nuts and bolts securely AdjustmentsTire Pressure Skid ShoesTesting Auger Drive Control Testing Wheel Drive Control & Speed Selector Shift LeverAdjusting Wheel Drive & Auger Controls Operation Recoil Starter Handle On / Off switchChute Assembly Clean-Out ToolGasoline Before Starting EngineStarting The Engine OilTo Engage Augers Replacing Shear PinsStopping The Engine To Engage Wheel DriveChanging Engine Oil Service and MaintenanceReinstall oil drain plug and tighten securely Checking Engine OilLubrication Shift Rod Shave Plate and Skid ShoesAuger Shaft Shave PlateBelt replacement Service and Maintenance Drive Belt Replacement Changing Friction WheelIf also replacing the drive belt, proceed to the Drive Belt Service and Maintenance Hole of the hex shaft Gas in the tank † Under heavy load or in high temperaturesWhile the engine is still warm, change the oil OFF-SEASON StoragePreparing Engine Preparing Snow ThrowerTroubleshooting Craftsman Snow Thrower Model Parts List39 -04020 Spacer, 1.004 x 1.375 x 721-0146 Housing, Auger 684-04151Parts List 84 -04484 Screw, 5/16-18 x 41 -0963 Connector, Shift Rod 684-0102A61 -0199A Bumper, Rubber 784-5619B 77 -1658 Lamp 725-1669Craftsman Snow Thrower Model 37 -0104 Pin, Internal Cotter From previous Page Page Page This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoverageGDOC-100182 Rev. a Here’s what the Repair Protection Agreement* includes Repair Protection AgreementNúmero DE Modelo ÍndiceDeclaración DE Garantía Especificaciones DEL ProductoInstrucciones DE Seguridad CapacitaciónPreparativos Mantenimiento y almacenamiento OperaciónMontaje Coloque la palanca de cambios en posición F6Montaje Extracción de la unidad del cajónDos fijadores de brida. Vea la Figura ConfiguraciónHerramienta de limpieza del canal Cortadores de desplazamiento de nieveAjustes Presión de los neumáticosZapatas antideslizantes Vuelva a ajustar bien las tuercas y los pernos Prueba de control de transmisión y palanca de cambiosPrueba del control de la transmisión de la barrena Vea Ajuste de transmisión y controles de barrenaOperación Barrenas Manija del arrancador de retro- cesoBotón del arrancador eléctrico Salida del arrancador eléctricoEncendido del motor Control direccional del canalHerramienta de limpieza Antes de encender el motorArrancador de retroceso Detención del motorProcedimiento para engranar la transmisión Procedimiento para engranar las barrenasCambio de aceite del motor Servicio Y MantenimientoMantenimiento de Motor Control del aceite del motorLubricación Control del canal Placa de raspado y zapatas antideslizantesPlaca de raspado Varilla de cambioControl de la barrena Cambio de correaControl de la transmisión Soporte del canalHolgazán de taladro es mantenida Reemplazo de la correa de la barrenaDel motor. Vea la Figura Nota Asegúrese que la posición del regatón en la vara deRanura de polea Adaptador Reemplazo de la correa de transmisiónBarrena al eje de entrada Motor e instale nuevamente la cubierta de la correaEje hexagonal Cambio de la rueda de fricciónDeslice el separador sobre el extremo del eje hexagonal Tanque † Bajo carga pesada o en temperaturas altas Cada Uso Nivel del aceite de motor ComprobarAlmacenaje a Corto plazo Almacenamiento Fuera DE TemporadaPreparación del motor Preparación de la máquina quitanieveSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Servicio de instalación de Sears Acuerdo DE Protección Para ReparacionesYour Home