Sanyo POA-MD13NET2 owner manual Compliance, Federal Communication Commission Notice

Page 2

Compliance

Federal Communication Commission Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Do not make any changes or modifications to the equipment unless otherwise speci- fied in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which cause the user may be required to take adequate measures.

CAUTION

This product provides a lithium battery. When you discard this product, you should return it to your local dealer.

CAUTION ON USE IN NETWORK

-When you receive an alert e-mail from the projector, you must check the projector immediately. Fire or accident may result if the projector is used in an abnormal condition.

-When you install the projector at remote location and use it through the network, you must perform the safety inspections periodically. In this case you must pay attention to the change of environment in which you installed the projector. It may cause fire or an accident depending on the change of environment.

CAUTION

We assume no responsibility for the loss or damage of data or damage of the com- puter caused by use of this product.

2

Image 2
Contents Installation and Operation of the Network Board Network BoardCompliance Federal Communication Commission NoticeContents AppendixB Chapter Controlling the Multi-ProjectorsChapter Use of Serial PortChapter Preparation Mail Alert function p.32 FeaturesWeb Management function p.36 Control port ready for external equipment via network p.62 Automatic On/Off using Timer function p.47Multi-control function p.56 Operating Environment Operating Environment Trademark Expression/AbbreviationUse of this manual Chapter Installation Flow of installation Set up is completedName and function of each part Installation and Network configuration MountingConnection of LAN cable Confirmation of the network menu Network configuration Type1Configure the network Selection of network menuRestart the Network board How to enter the numbersCompleting of installation Entering the Network PIN code Network PIN code settingDisplaying Network PIN code menu Fixing the Network PIN codeHow to enter the numbers with the screen 10-key pallet Network configuration Type2 Selection of network menu NetworkNetwork Setting Password setting Display English Installation Chapter Basic Setting and Operation Enter the IP address Login the setting page of the projectorSelect a display mode and login Display of main setting Main setting page in the Graphic Mode displayMain setting page in the Text Mode display Initial Settings Language SettingPassword Setting Date/Time SettingName the projector Network ConfigurationConfigure the network Mail Setting Registering Smtp Server*1, Administrator AddressRegistering and deleting E-mail addresses Condition selection for sending alert messageExamples Type and contents of alert mail Chapter Controlling the Projector Power on/off the projector Check the status of projector Items DescriptionControl the projector InputPC Adjustment PictureSave a Set Load a SetAvailable selection when the Y, Cb/Pb, Cr/Pr input System AdjustmentAvailable selection when the VIDEO/S-VIDEO input Image Adjustment Image adjustment valuesSave a image adjustment value Load a image modeScreen Adjustment Sound AdjustmentSetting Freeze................Sets the image frozen mode PowerAbout Lamp Counter reset Switching two lampsSets the HD data wireless How to set the Timer Check the Timer eventsCancel the timer Getting the current timeService Ing on the projectors functionSave Actual Adjustment Check the Save itemsLoad a control set Control the projectors menu ProjectorMake a memo Chapter Controlling the Multi-Projectors Multi-Control Internet IntranetRegister IP address and projector name Check IP address and projector nameExclude/Add/Delete a projector StatusLoad and apply the setting value ControlControl multi-projectors at the same time Chapter Use of Serial Port Serial Port setting Connected to the serial portSerial Port Setting Control Examples ExampleSerial Port Switching Use of Telnet PreparationFor example, entering pass- word Command list table Control the projector with TelnetConnection examples Web browser setting Technical data Chapter AppendixAExamples of Connection Peer-To-Peer connectionGateway Router installed in the network TheaterProxy setting Web browser settingActive Script/JavaScript enable Windows XP Professional Internet Explorer ActiveScript settingExamples OS/Browsers Proxy setting Netscape Navigator JavaScript Setting Proxy setting Internet Explorer ActiveScript setting Mac OSProxy setting Netscape Navigator JavaScript Setting Proxy setting Product specification TCP/IPSerial port specification Port SpecificationLAN port specification AppendixB Installation/Access Why doesn’t the setting page appear in my web browser?How can I restrict access from the computer Password/Login What should I do when I forget the password?Operation Why am I not receiving E-mail alert messages? Can I control the projector by using the telnet application?Can I update the firmware of the Network Board What is the MAC address assigned to the Network Board? What are the rules for IP address assignment?English Idrmd built in KJ5AL b