Sanyo POA-MD13NET2 Port Specification, LAN port specification, Serial port specification

Page 82

Chapter 7 Appendix

Port Specification

LAN port specification

8-pin modular connector (RJ-45)

1 2 3 4 5 6 7 8

pin No.

Signal

Function

 

 

 

1

TX+

Transfer data (+)

2

TX-

Transfer data (-)

3

RD+

Receive data (+)

4

(not used)

 

5

(not used)

 

6

RD-

Receive data (-)

7

(not used)

 

8

(not used)

 

 

 

 

Serial port specification

D sub 9-pin connector (RS-232C)

5 4 3 2 1

9 8 7 6

*It is possible to switch the polarity of the serial port as shown in table below by switching the socket on the network board. For further information, see item "Serial Port Switching" (p.65). At the factory shipped setting, the socket is set to side A.

Pin No.

 

Signal Name

Socket

Side A

 

Side B

 

 

 

 

1

CD

 

-

2

RXD

 

TXD

3

TXD

 

RXD

4

DTR

 

-

5

Ground

 

Ground

6

DSR

 

-

7

RTS

 

-

8

CTS

 

-

9

-

 

-

 

 

 

 

- Explanation of signal names

Function

CD Carrier detection RXD Receive data TXD Transfer data DTR Data terminal ready DSR Data set ready

RTS Request to send

CTS Clear to send

-Not used

82

Image 82
Contents Installation and Operation of the Network Board Network BoardCompliance Federal Communication Commission NoticeContents AppendixB Chapter Controlling the Multi-ProjectorsChapter Use of Serial PortChapter Preparation Web Management function p.36 FeaturesMail Alert function p.32 Multi-control function p.56 Automatic On/Off using Timer function p.47Control port ready for external equipment via network p.62 Operating Environment Operating Environment Use of this manual Expression/AbbreviationTrademark Chapter Installation Flow of installation Set up is completedName and function of each part Installation and Network configuration MountingConnection of LAN cable Confirmation of the network menu Network configuration Type1Configure the network Selection of network menuCompleting of installation How to enter the numbersRestart the Network board Entering the Network PIN code Network PIN code settingDisplaying Network PIN code menu Fixing the Network PIN codeHow to enter the numbers with the screen 10-key pallet Network configuration Type2 Selection of network menu NetworkNetwork Setting Password setting Display English Installation Chapter Basic Setting and Operation Select a display mode and login Login the setting page of the projectorEnter the IP address Display of main setting Main setting page in the Graphic Mode displayMain setting page in the Text Mode display Initial Settings Language SettingPassword Setting Date/Time SettingConfigure the network Network ConfigurationName the projector Mail Setting Registering Smtp Server*1, Administrator AddressRegistering and deleting E-mail addresses Condition selection for sending alert messageExamples Type and contents of alert mail Chapter Controlling the Projector Power on/off the projector Check the status of projector Items DescriptionControl the projector InputPC Adjustment PictureSave a Set Load a SetAvailable selection when the VIDEO/S-VIDEO input System AdjustmentAvailable selection when the Y, Cb/Pb, Cr/Pr input Image Adjustment Image adjustment valuesSave a image adjustment value Load a image modeScreen Adjustment Sound AdjustmentSetting Freeze................Sets the image frozen mode PowerAbout Lamp Counter reset Switching two lampsSets the HD data wireless How to set the Timer Check the Timer eventsCancel the timer Getting the current timeService Ing on the projectors functionSave Actual Adjustment Check the Save itemsLoad a control set Control the projectors menu ProjectorMake a memo Chapter Controlling the Multi-Projectors Multi-Control Internet IntranetRegister IP address and projector name Check IP address and projector nameExclude/Add/Delete a projector StatusLoad and apply the setting value ControlControl multi-projectors at the same time Chapter Use of Serial Port Serial Port setting Connected to the serial portSerial Port Setting Control Examples ExampleSerial Port Switching Use of Telnet PreparationFor example, entering pass- word Command list table Control the projector with TelnetConnection examples Web browser setting Technical data Chapter AppendixAExamples of Connection Peer-To-Peer connectionGateway Router installed in the network TheaterActive Script/JavaScript enable Web browser settingProxy setting Examples OS/Browsers Internet Explorer ActiveScript settingWindows XP Professional Proxy setting Netscape Navigator JavaScript Setting Proxy setting Internet Explorer ActiveScript setting Mac OSProxy setting Netscape Navigator JavaScript Setting Proxy setting Product specification TCP/IPLAN port specification Port SpecificationSerial port specification AppendixB Installation/Access Why doesn’t the setting page appear in my web browser?How can I restrict access from the computer Password/Login What should I do when I forget the password?Operation Why am I not receiving E-mail alert messages? Can I control the projector by using the telnet application?Can I update the firmware of the Network Board What is the MAC address assigned to the Network Board? What are the rules for IP address assignment?English Idrmd built in KJ5AL b