Sanyo POA-MD13NET2 owner manual Control the projector with Telnet, Command list table

Page 68

Chapter 6 Use of Serial Port

Control the projector with Telnet

This product allows you to control the projector by using the Telnet application. Normally, it is used for controlling the external equipment connected to the serial port and also control the projector itself by specifying the telnet port no.10000.

*It is not affected by the serial port setting of the projector when using the telnet appli- cation.

In the step 2 of the previous page, enter port no. “10000” after the IP address no. > open 192.168.1.201 10000 return

* Use the IP address assigned to the pro- jector

After the communication is established, type the password and the command for controlling the projector and then enter “Enter” key.

The right table shows the typical command lists for controlling the our projector and please consult your local dealer for further information of another commands.

Command list table

Command	Function

C00	Turn the projector on
C01	Turn the projector off
C05	Selects input1
C06	Selects input2
C07	Selects input3
C08	Selects input4
C09	Volume up
C0A	Volume down
C0B	Mute on
C0C	Mute off
C0D	Video mute on
C0E	Video mute off
C1C	Menu display on
C1D	menu display off

68

Image 68

Contents Installation and Operation of the Network Board Network BoardCompliance Federal Communication Commission NoticeContents Chapter Controlling the Multi-Projectors ChapterAppendixB Use of Serial PortChapter Preparation Mail Alert function p.32 FeaturesWeb Management function p.36 Control port ready for external equipment via network p.62 Automatic On/Off using Timer function p.47Multi-control function p.56 Operating Environment Operating Environment Trademark Expression/AbbreviationUse of this manual Chapter Installation Flow of installation Set up is completedName and function of each part Installation and Network configuration MountingConnection of LAN cable Network configuration Type1 Configure the networkConfirmation of the network menu Selection of network menuRestart the Network board How to enter the numbersCompleting of installation Network PIN code setting Displaying Network PIN code menuEntering the Network PIN code Fixing the Network PIN codeHow to enter the numbers with the screen 10-key pallet Network configuration Type2 Selection of network menu NetworkNetwork Setting Password setting Display English Installation Chapter Basic Setting and Operation Enter the IP address Login the setting page of the projectorSelect a display mode and login Display of main setting Main setting page in the Graphic Mode displayMain setting page in the Text Mode display Initial Settings Language SettingPassword Setting Date/Time SettingName the projector Network ConfigurationConfigure the network Mail Setting Registering Smtp Server*1, Administrator AddressRegistering and deleting E-mail addresses Condition selection for sending alert messageExamples Type and contents of alert mail Chapter Controlling the Projector Power on/off the projector Check the status of projector Items DescriptionControl the projector InputPC Adjustment PictureSave a Set Load a SetAvailable selection when the Y, Cb/Pb, Cr/Pr input System AdjustmentAvailable selection when the VIDEO/S-VIDEO input Image Adjustment Image adjustment valuesSave a image adjustment value Load a image modeScreen Adjustment Sound AdjustmentSetting Freeze................Sets the image frozen mode PowerAbout Lamp Counter reset Switching two lampsSets the HD data wireless How to set the Timer Check the Timer eventsCancel the timer Getting the current timeService Ing on the projectors functionSave Actual Adjustment Check the Save itemsLoad a control set Control the projectors menu ProjectorMake a memo Chapter Controlling the Multi-Projectors Multi-Control Internet IntranetRegister IP address and projector name Check IP address and projector nameExclude/Add/Delete a projector StatusLoad and apply the setting value ControlControl multi-projectors at the same time Chapter Use of Serial Port Serial Port setting Connected to the serial portSerial Port Setting Control Examples ExampleSerial Port Switching Use of Telnet PreparationFor example, entering pass- word Command list table Control the projector with TelnetConnection examples Web browser setting Technical data Chapter AppendixAExamples of Connection Peer-To-Peer connectionGateway Router installed in the network TheaterProxy setting Web browser settingActive Script/JavaScript enable Windows XP Professional Internet Explorer ActiveScript settingExamples OS/Browsers Proxy setting Netscape Navigator JavaScript Setting Proxy setting Internet Explorer ActiveScript setting Mac OSProxy setting Netscape Navigator JavaScript Setting Proxy setting Product specification TCP/IPSerial port specification Port SpecificationLAN port specification AppendixB Installation/Access Why doesn’t the setting page appear in my web browser?How can I restrict access from the computer Password/Login What should I do when I forget the password?Operation Why am I not receiving E-mail alert messages? Can I control the projector by using the telnet application?Can I update the firmware of the Network Board What is the MAC address assigned to the Network Board? What are the rules for IP address assignment?English Idrmd built in KJ5AL b