Sanyo POA-MD13NET2 owner manual Sets the HD data wireless

Page 47

 

 

 

Control the Projector

 

 

Item

Description

 

 

 

 

 

 

 

 

HD data wireless

Sets the HD data wireless

 

 

 

board.

 

 

Mode select

Switches the communication

 

 

 

mode (Single mode or

 

 

 

Broadcast mode).

 

 

Authentication ....

Executes or resets the authen-

 

 

 

tication at the Single mode.

 

 

ID input

Inputs ID number at the broad-

 

 

 

cast mode.

 

 

Reset

Restore the value of the HD

 

 

 

data wireless setting items to

 

 

 

the factory default value.

 

 

 

*There may not be available depending on the projector's model type.

Item Description

Picture in Picture ......Sets the “P in P” or “P by P”

mode which has been preset in the setting menu. (OFF, User1 - User5)

Edge blending....Sets the seamless overlapping

for multi-screen.

Color matching ..Corrects the difference of color for multi-screen.

DynamicBlack ....Improve the black level of the

image. (OFF/Low/High)

HDMI setup........Switches Normal or Enhanced

according to the HDMI source.

* There may not be available depending on the projector's model type.

When the Picture in Picture mode is ON, there are some restrictions as follows; - The last memorized input source is displayed in Input menu.

- “PC Adjustment”, “System Adjustment” and “Save Adjustment” are invalid.

Network Board

OWNER’S MANUAL

ENGLISH

47

Image 47
Contents Network Board Installation and Operation of the Network BoardFederal Communication Commission Notice ComplianceContents Use of Serial Port Chapter Controlling the Multi-ProjectorsChapter AppendixBChapter Preparation Mail Alert function p.32 FeaturesWeb Management function p.36 Control port ready for external equipment via network p.62 Automatic On/Off using Timer function p.47Multi-control function p.56 Operating Environment Operating Environment Trademark Expression/AbbreviationUse of this manual Chapter Installation Set up is completed Flow of installationName and function of each part Mounting Installation and Network configurationConnection of LAN cable Selection of network menu Network configuration Type1Configure the network Confirmation of the network menuRestart the Network board How to enter the numbersCompleting of installation Fixing the Network PIN code Network PIN code settingDisplaying Network PIN code menu Entering the Network PIN codeHow to enter the numbers with the screen 10-key pallet Selection of network menu Network Network configuration Type2Network Setting Password setting Display English Installation Chapter Basic Setting and Operation Enter the IP address Login the setting page of the projectorSelect a display mode and login Main setting page in the Graphic Mode display Display of main settingMain setting page in the Text Mode display Language Setting Initial SettingsDate/Time Setting Password SettingName the projector Network ConfigurationConfigure the network Registering Smtp Server*1, Administrator Address Mail SettingCondition selection for sending alert message Registering and deleting E-mail addressesExamples Type and contents of alert mail Chapter Controlling the Projector Power on/off the projector Items Description Check the status of projectorInput Control the projectorPicture PC AdjustmentLoad a Set Save a SetAvailable selection when the Y, Cb/Pb, Cr/Pr input System AdjustmentAvailable selection when the VIDEO/S-VIDEO input Image adjustment values Image AdjustmentLoad a image mode Save a image adjustment valueSound Adjustment Screen AdjustmentFreeze................Sets the image frozen mode Power SettingSwitching two lamps About Lamp Counter resetSets the HD data wireless Check the Timer events How to set the TimerGetting the current time Cancel the timerIng on the projectors function ServiceCheck the Save items Save Actual AdjustmentLoad a control set Projector Control the projectors menuMake a memo Chapter Controlling the Multi-Projectors Internet Intranet Multi-ControlCheck IP address and projector name Register IP address and projector nameStatus Exclude/Add/Delete a projectorControl Load and apply the setting valueControl multi-projectors at the same time Chapter Use of Serial Port Connected to the serial port Serial Port settingSerial Port Setting Example Control ExamplesSerial Port Switching Preparation Use of TelnetFor example, entering pass- word Control the projector with Telnet Command list tableChapter AppendixA Connection examples Web browser setting Technical dataPeer-To-Peer connection Examples of ConnectionTheater Gateway Router installed in the networkProxy setting Web browser settingActive Script/JavaScript enable Windows XP Professional Internet Explorer ActiveScript settingExamples OS/Browsers Proxy setting Netscape Navigator JavaScript Setting Proxy setting Mac OS Internet Explorer ActiveScript settingProxy setting Netscape Navigator JavaScript Setting Proxy setting TCP/IP Product specificationSerial port specification Port SpecificationLAN port specification AppendixB Why doesn’t the setting page appear in my web browser? Installation/AccessHow can I restrict access from the computer What should I do when I forget the password? Password/LoginOperation Can I control the projector by using the telnet application? Why am I not receiving E-mail alert messages?Can I update the firmware of the Network Board What are the rules for IP address assignment? What is the MAC address assigned to the Network Board?English Idrmd built in KJ5AL b