NEC PD75P308 user manual Appendix A. Development Tools, Prom writing tools

Page 31

μPD75P308

APPENDIX A. DEVELOPMENT TOOLS

The following development support tools are readily available to support development of systems using μPD75P308:

PROM writing tools

Hardare	IE-75000-R*1		In-circuit emulator for 75K series
	IE-75001-R
	IE-75000-R-EM*2		Emulation board for IE-75000-R and IE-75001-R
	EP-75308GF-R		Emulation prove for μPD75P308GF, provided with 80-pin conversion socket,

		EV-9200G-80	EV-9200G-80.
	PG-1500		PROM programmer
	PA-75P308GF		PROM programmer adapter solely used for μPD75P308GF. It is connected to
			PG-1500.
	PA-75P308K		PROM programmer adapter solely used for μPD75P308K. It is connected to
			PG-1500.

Software	IE Control Program		Host machine

	PG-1500 Controller		• PC-9800 series (MS-DOSTMVer.3.30 to Ver.5.00A*3)
	RA75X Relocatable		• IBM PC/ATTM (PC DOSTM Ver.3.1)
	Assembler

*1: Maintenance product

2:Not provided with IE-75001-R

3:Ver.5.00/5.00A has a task swap function, but this function cannot be used with this software.

Remarks: For development tools from other companies, refer to 75X Series Selection Guide (IF-151).

31

Image 31

Contents Quality Grade FeaturesDescription Ordering InformationΜPD75P308 PIN ConfigurationBlock Diagram Contents PIN Functions Port PinsNON Port Pins PIN INPUT/OUTPUT Circuits Schmitt trigger input with hysteresis characteristicsInput buffer of Cmos standard Type F-B COMIN/OUT SEG Type M-C Connect capacitor between VDD and P00/INT4, Reset pinEprom Differences Between μPD75P308 and μPD75308Operation Modes for WRITING/VERIFYING Program Memory Program memory address 0 clear mode+12.5 Write mode Verify mode Program inhibit mode Or H Writing and Verifying Prom Program MemoryVDD+1 Program Memory Write ProcedureProgram Memory Read Procedure Erasure μPD75P308K only Absolute Maximum Ratings Ta = 25C Electrical SpecificationsMain System Clock Ceramic Oscillator Ta = -10 to +70C Main System Clock Oscillator Circuit CharacteristicsTa = -10 to +70C, VDD = 5 to ±5 Recommended Oscillation Circuit ConstantsCapacitance Ta = 25C, VDD = 0 DC Characteristics Ta = -10 to +70C, VDD = 5V ±5% Interrupt mode register IM0 AC Characteristics Ta = -10 to + 70C, VDD = 5V ±5%Operation Other Than Serial Transfer Serial Transfer Operation SBI Mode SCK external clock output master SBI Mode SCK internal clock output masterClock Timing AC Timing Test Point excluding X1 and XT1 inputsTI0 Timing TWO-LINE Serial I/O Mode Serial Transfer Timing THREE-LINE Serial I/O ModeInterrupt Input Timing Serial Transfer Timing BUS Release Signal TransferCommand Signal Transfer Reset Input TimingTa = -10 to +70C Data Retention Timing releasing Stop mode by ResetBTM3 BTM2 BTM1 BTM0 Other than X1 or Program Memory Read Timing Program Memory Write TimingMD0 MD1 PIN Plastic QFP 14×20 Package DrawingsMillimeters Inches PIN Ceramic WqfnΜPD75P308GF-3B9 80-pin plastic QFP 14 x 20 mm Recommended Soldering ConditionsVPS Prom writing tools Appendix A. Development ToolsAppendix B. Related Documents Fix the input level of Cmos devices Processing of Unused Pins Cmos Devices onlyStatic Electricity ALL MOS Devices Status Before Initialization ALL MOS DevicesMemo