NEC PD75P308 Static Electricity ALL MOS Devices, Processing of Unused Pins Cmos Devices only

Page 33

μPD75P308

GENERAL NOTES ON CMOS DEVICES

1 STATIC ELECTRICITY (ALL MOS DEVICES)

Exercise care so that MOS devices are not adversely influenced by static electricity while being

handled.

The insulation of the gates of the MOS device may be destroyed by a strong static charge. Therefore, when transporting or storing the MOS device, use a conductive tray, magazine case, or conductive buffer materials, or the metal case NEC uses for packaging and shipment, and use grounding when assembling the MOS device system. Do not leave the MOS device on a plastic plate and do not touch the pins of the device.

Handle boards on which MOS devices are mounted similarly .

2 PROCESSING OF UNUSED PINS (CMOS DEVICES ONLY)

Fix the input level of CMOS devices.

Unlike bipolar or NMOS devices, if a CMOS device is operated with nothing connected to its input pin, intermediate level input may be generated due to noise, and an inrush current may flow through the device, causing the device to malfunction. Therefore, fix the input level of the device by using a pull-down or pull-up resistor. If there is a possibility that an unused pin serves as an output pin (whose timing is not specified), each pin should be connected to VDD or GND through a resistor.

Refer to “Processing of Unused Pins” in the documents of each devices.

3 STATUS BEFORE INITIALIZATION (ALL MOS DEVICES)

The initial status of MOS devices is undefined upon power application.

Since the characteristics of an MOS device are determined by the quantity of injection at the molecular level, the initial status of the device is not controlled during the production process. The output status of pins, I/O setting, and register contents upon power application are not guaranteed. However, the items defined for reset operation and mode setting are subject to guarantee after the respective operations have been executed.

When using a device with a reset function, be sure to reset the device after power application.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Description FeaturesOrdering Information Quality GradeΜPD75P308 PIN ConfigurationBlock Diagram Contents PIN Functions Port PinsNON Port Pins Schmitt trigger input with hysteresis characteristics PIN INPUT/OUTPUT CircuitsInput buffer of Cmos standard COM Type F-BIN/OUT SEG Type M-C Connect capacitor between VDD and P00/INT4, Reset pinEprom Differences Between μPD75P308 and μPD75308+12.5 Write mode Verify mode Program inhibit mode Or H Program memory address 0 clear modeWriting and Verifying Prom Program Memory Operation Modes for WRITING/VERIFYING Program MemoryVDD+1 Program Memory Write ProcedureProgram Memory Read Procedure Erasure μPD75P308K only Absolute Maximum Ratings Ta = 25C Electrical SpecificationsTa = -10 to +70C, VDD = 5 to ±5 Main System Clock Oscillator Circuit CharacteristicsRecommended Oscillation Circuit Constants Main System Clock Ceramic Oscillator Ta = -10 to +70CCapacitance Ta = 25C, VDD = 0 DC Characteristics Ta = -10 to +70C, VDD = 5V ±5% AC Characteristics Ta = -10 to + 70C, VDD = 5V ±5% Interrupt mode register IM0Operation Other Than Serial Transfer Serial Transfer Operation SBI Mode SCK external clock output master SBI Mode SCK internal clock output masterAC Timing Test Point excluding X1 and XT1 inputs Clock TimingTI0 Timing TWO-LINE Serial I/O Mode Serial Transfer Timing THREE-LINE Serial I/O ModeCommand Signal Transfer Serial Transfer Timing BUS Release Signal TransferReset Input Timing Interrupt Input TimingData Retention Timing releasing Stop mode by Reset Ta = -10 to +70CBTM3 BTM2 BTM1 BTM0 Other than X1 or Program Memory Write Timing Program Memory Read TimingMD0 MD1 PIN Plastic QFP 14×20 Package DrawingsMillimeters Inches PIN Ceramic WqfnRecommended Soldering Conditions ΜPD75P308GF-3B9 80-pin plastic QFP 14 x 20 mmVPS Prom writing tools Appendix A. Development ToolsAppendix B. Related Documents Static Electricity ALL MOS Devices Processing of Unused Pins Cmos Devices onlyStatus Before Initialization ALL MOS Devices Fix the input level of Cmos devicesMemo
Top Page Image Contents