Kodak A-61580 manual

Page 51

•Custom: allows you to manually adjust the Color amount and/or Color threshold.

NOTE: When setting Sensitivity values, it is suggested that you start with the Medium option and scan a typical job set. If too many documents were returned as color/grayscale vs. black and white, then change to the High option and re-run the job. If too few documents were returned as color/grayscale vs. black and white, then change to the Low option and re-run the job. If none of these options provide the desired result, select Custom to manually adjust Color amount and/or Color threshold. Custom also allows access to the Learn mode which provides a method for the scanner to analyze documents and recommend settings.

Color amount — the amount of color that needs to be present in a document before it will be saved as color/grayscale. As the value of Color amount increases, more color pixels are required. The options range from 1 to 200.

Color threshold — the color threshold or saturation (i.e., pale blue vs. dark blue) at which a given color will be included in the color amount calculation. A higher value indicates that a more intense color is required. The options range from 0 to 100.

Learn — allows you to calculate your settings based on representative color documents scanned. Before clicking Learn, place at least 5 representative color documents in the input elevator. The documents will be scanned and analyzed to determine the recommended color amount.

NOTE: The Color amount and Color threshold sliders will be updated automatically. If these values do not provide the desired results with your job set, you may need to adjust the Color threshold manually.

A-61580 November 2007

3-23

Image 51

Contents Page About this manual IntroductionImage outputs FG.jpg Best Practices Scanner setup Initiate polling Error handlingEnable scanning Disable scanningPage Controlling image transfer order Dual stream duplex Dual stream simplexPage Jam and fault recovery Image address format Image file storage locationsBar code recognition Image addressingSingle level indexing Starting image addressNext image address Indexing schemesTwo level indexing Two level offset indexing Three level indexing Three level offset indexing Generated Automatically Print string formatting Electronic color dropoutLevel rules Controlling print stringsRed Dropout  Near Complete Dropout Resolution = 200 dpiContrast% = Threshold = Color Filter = Red dropoutBlue Dropout  Near Complete Dropout Green Dropout  Complete DropoutGreen Dropout  Near Complete Dropout Blue Dropout  Complete DropoutImage header information Page Original Black and white image Relative Cropping Zone processingType 3 Patch Code Programmable keysPatch reading Patch code typesTransfer Patch Code Toggle PatchAdditional Patch Codes Batching Installation Overview Terminology and features Using the Twain DatasourceValidation Tool Accessing the ScanValidation tool Select StartProgramsKodakDocument ImagingScanPage Main Kodak Scanner window Page Information icons Image Settings window Preview area Toolbar buttonsInformation icons Cases you will not have to change options on other tabs TabPage November None Landscape Degrees Image Settings Adjustments tabScan as selection of Black and White Image None Filters Noise NoneEnhancements tab Advanced Image Setup Input document is select Two Sided, One Sided Front, or One Advanced tabPage Done returns you to the Image Settings window November Sensitivity Content Settings tabPage Select Grayscale Select Sides Both Black and White 1-bit Select Sides Both Color 24-bitMake sure Black and White 1-bit is selected Creating multiple images for each side of a documentSelect Sides Both Color 24-bit Creating different settings for each side of a document Select Sides FrontSelect Sides Back Device Settings window Device General tab Paper sourceDocument Feeder Page Device Printer tab Page Yyyyddd Julian Date FormatFeed Direction 180 270 Ultrasonic detection Page Template Do Not Display e.g., A.3.2.1 Display as Spaces e.g., a When Count Reached Device Batch tabReached. Options are none, Level 1, Level 2, and Level November As Level Device Patch tabFeature Device OCP tab Creating a new Setting Shortcut Page Page Main Isis Driver window Using the Isis DriverMain tab Image ModePage Page Image Orientation Layout tabGeneral options When Fixed to Transport or Relative to Document is selectedSuperior Color optionsScanner tab Options TimeoutPower Saver Multi-feed DetectionPage Operations Page Color Content Learn Dropout tab Color DropoutBlank Image Detection Mode Imprinter tabDefining your print string Hyphen -, Period . , Blank or none. For example 08/24/2007Units select Inches, Centimeters or Pixels Image Address tab Level 2 Offset Address%2L Transport End of Job, Continue and Begin New Batch or no Batch/Patch tabBatch Control Go to Level 3 or no actionLevel 2 or Patch T / Transfer Patch Level Patch DetectionPatch 4/Toggle Patch PatchOCP tab Operator Log tab About tab Page Area Appendix a Twain Image Processing Terminology Feature Cropping