Kodak A-61580 manual Ultrasonic detection

Page 64

Device - Multifeed tab Multifeed detection aids in document processing by detecting documents that may go through the feeder overlapped. Multifeeds can happen due to stapled documents, adhesives on documents, or electrostatically charged documents.

Ultrasonic detection

Sensitivity — controls how aggressively the scanner will work to determine if more than one document is fed into the scanner. Multifeeds are triggered by detecting air gaps between documents. This allows multifeed detection to be used with job sets containing documents with mixed thicknesses.

(none)

Low: least aggressive setting and is less likely to detect labels, poor quality, thick or wrinkled documents as multi-fed documents.

Medium: use if your job set has varying document thicknesses or labels attached to the document. Depending on the label material, most documents with labels should not be detected as a multi-fed document.

High: most aggressive setting. This is a good setting to use if all documents are similar in thickness no greater than 20-lb. bond paper.

NOTE: Regardless of the setting, “sticky” notes will be detected as multi-fed documents.

3-36

A-61580 November 2007

Image 64
Contents Page Introduction About this manualImage outputs FG.jpg Best Practices Scanner setup Error handling Enable scanningDisable scanning Initiate pollingPage Controlling image transfer order Dual stream simplex Dual stream duplexPage Jam and fault recovery Image file storage locations Bar code recognitionImage addressing Image address formatStarting image address Next image addressIndexing schemes Single level indexingTwo level indexing Two level offset indexing Three level indexing Three level offset indexing Generated Automatically Electronic color dropout Level rulesControlling print strings Print string formattingResolution = 200 dpi Contrast% = Threshold = Color Filter =Red dropout Red Dropout  Near Complete DropoutGreen Dropout  Complete Dropout Green Dropout  Near Complete DropoutBlue Dropout  Complete Dropout Blue Dropout  Near Complete DropoutImage header information Page Zone processing Original Black and white image Relative CroppingProgrammable keys Patch readingPatch code types Type 3 Patch CodeToggle Patch Transfer Patch CodeAdditional Patch Codes Batching Using the Twain Datasource Installation Overview Terminology and featuresAccessing the Scan Validation toolSelect StartProgramsKodakDocument ImagingScan Validation ToolPage Main Kodak Scanner window Page Information icons Image Settings window Toolbar buttons Preview areaInformation icons Tab Cases you will not have to change options on other tabsPage November None Landscape Degrees Adjustments tab Image SettingsScan as selection of Black and White Filters Noise None Image NoneEnhancements tab Advanced Image Setup Advanced tab Input document is select Two Sided, One Sided Front, or OnePage Done returns you to the Image Settings window November Content Settings tab SensitivityPage Select Grayscale Select Sides Both Color 24-bit Select Sides Both Black and White 1-bitCreating multiple images for each side of a document Make sure Black and White 1-bit is selectedSelect Sides Both Color 24-bit Select Sides Front Creating different settings for each side of a documentSelect Sides Back Device Settings window Paper source Device General tabDocument Feeder Page Device Printer tab Page Date Format Yyyyddd JulianFeed Direction 180 270 Ultrasonic detection Page Template Do Not Display e.g., A.3.2.1 Display as Spaces e.g., a Device Batch tab When Count ReachedReached. Options are none, Level 1, Level 2, and Level November Device Patch tab As LevelFeature Device OCP tab Creating a new Setting Shortcut Page Page Using the Isis Driver Main Isis Driver windowImage Mode Main tabPage Page Layout tab Image OrientationWhen Fixed to Transport or Relative to Document is selected General optionsColor options SuperiorScanner tab Timeout Power SaverMulti-feed Detection OptionsPage Operations Page Color Content Learn Color Dropout Dropout tabBlank Image Detection Imprinter tab ModeHyphen -, Period . , Blank or none. For example 08/24/2007 Defining your print stringUnits select Inches, Centimeters or Pixels Image Address tab Level 2 Offset Address%2L Batch/Patch tab Batch ControlGo to Level 3 or no action Transport End of Job, Continue and Begin New Batch or noPatch Detection Level 2 or Patch T / Transfer Patch LevelPatch Patch 4/Toggle PatchOCP tab Operator Log tab About tab Page Area Appendix a Twain Image Processing Terminology Feature Cropping