Kodak A-61580 manual Batching

Page 28

Batching	Batching information only applies when the scanner is configured with
	Image Address enabled via the operator control panel touchscreen.
	Batching provides a way for the scanner to perform a specific function
	after scanning a designated number of documents at a particular IA
	level.
	Batching can be enabled or disabled through the host software. The
	host software has control of which level to count and the number of
	documents to designate a batch.
	The Start of Batch function is controlled by the host and determines
	what happens when a new batch is started. This can be setup to go to
	Level 1, 2 or 3, which then causes the IA to be recalculated. The Start
	of Batch function can also be set to no function.
	The End of Batch function is controlled by the host and determines
	what happens when the batch count has been reached. The options
	are to stop the feeder, end of job, or continue and begin a new batch.
	No functionality can also be assigned.
	The host application determines if batching is enabled by defining the
	number of documents per batch and the image address level to count.

2-24	A-61580 November 2007

Image 28

Contents Page Introduction About this manualImage outputs FG.jpg Best Practices Scanner setup Error handling Enable scanningDisable scanning Initiate pollingPage Controlling image transfer order Dual stream simplex Dual stream duplexPage Jam and fault recovery Image file storage locations Bar code recognitionImage addressing Image address formatStarting image address Next image addressIndexing schemes Single level indexingTwo level indexing Two level offset indexing Three level indexing Three level offset indexing Generated Automatically Electronic color dropout Level rulesControlling print strings Print string formattingResolution = 200 dpi Contrast% = Threshold = Color Filter =Red dropout Red Dropout  Near Complete DropoutGreen Dropout  Complete Dropout Green Dropout  Near Complete DropoutBlue Dropout  Complete Dropout Blue Dropout  Near Complete DropoutImage header information Page Zone processing Original Black and white image Relative CroppingProgrammable keys Patch readingPatch code types Type 3 Patch CodeToggle Patch Transfer Patch CodeAdditional Patch Codes Batching Using the Twain Datasource Installation Overview Terminology and featuresAccessing the Scan Validation toolSelect StartProgramsKodakDocument ImagingScan Validation ToolPage Main Kodak Scanner window Page Information icons Image Settings window Toolbar buttons Preview areaInformation icons Tab Cases you will not have to change options on other tabsPage November None Landscape Degrees Adjustments tab Image SettingsScan as selection of Black and White Filters Noise None Image NoneEnhancements tab Advanced Image Setup Advanced tab Input document is select Two Sided, One Sided Front, or OnePage Done returns you to the Image Settings window November Content Settings tab SensitivityPage Select Grayscale Select Sides Both Color 24-bit Select Sides Both Black and White 1-bitCreating multiple images for each side of a document Make sure Black and White 1-bit is selectedSelect Sides Both Color 24-bit Select Sides Front Creating different settings for each side of a documentSelect Sides Back Device Settings window Paper source Device General tabDocument Feeder Page Device Printer tab Page Date Format Yyyyddd JulianFeed Direction 180 270 Ultrasonic detection Page Template Do Not Display e.g., A.3.2.1 Display as Spaces e.g., a Device Batch tab When Count ReachedReached. Options are none, Level 1, Level 2, and Level November Device Patch tab As LevelFeature Device OCP tab Creating a new Setting Shortcut Page Page Using the Isis Driver Main Isis Driver windowImage Mode Main tabPage Page Layout tab Image OrientationWhen Fixed to Transport or Relative to Document is selected General optionsColor options SuperiorScanner tab Timeout Power SaverMulti-feed Detection OptionsPage Operations Page Color Content Learn Color Dropout Dropout tabBlank Image Detection Imprinter tab ModeHyphen -, Period . , Blank or none. For example 08/24/2007 Defining your print stringUnits select Inches, Centimeters or Pixels Image Address tab Level 2 Offset Address%2L Batch/Patch tab Batch ControlGo to Level 3 or no action Transport End of Job, Continue and Begin New Batch or noPatch Detection Level 2 or Patch T / Transfer Patch LevelPatch Patch 4/Toggle PatchOCP tab Operator Log tab About tab Page Area Appendix a Twain Image Processing Terminology Feature Cropping