FARGO electronic Card Printer manual Adjusting the Internal Card Guide

Page 64

4250/4225 Card Printer UserÕs Manual

B. ADJUSTING THE INTERNAL CARD GUIDE

The printer is equipped with a spring-loaded Internal Card Guide which automatically adjusts to the width of your card stock. Depending on the thickness of your card stock, however, you may need to adjust the tension of the Internal Card GuideÕs spring. This is a very simple adjustment and is done by moving the card guideÕs Tension Lever to the appropriate position.

The default position of the Tension Lever is toward the front of the printer. This provides higher spring tension which is necessary for printing onto standard card sizes with a thickness of .030Ó/.75mm or higher. If using thinner cards, such as those with a .010Ó/.25mm thickness, move the Tension Lever toward the rear of the printer. This decreases the spring tension allowing the Internal Card Guide to accommodate the less rigid nature of thinner cards.

Internal Card Guide

Move here for thinner cards (.010”/.25 mm)

Move here for thicker cards (.030”/.75 mm or higher)

Tension Lever

NOTE: It is important the tension of the Card Input Guide is set properly. If spring tension is increased and you are using thinner cards, you may experience card jams. If spring tension is decreased and you are using cards with a standard thickness, printed cards may appear misregistered or blurry.

C. ADJUSTING THE CARD SEPARATOR FLAP

The Card Separator Flap resides inside the printer and helps prevent two cards from feeding simultaneously. This flap is adjustable to accommodate varying card thicknesses. Although the Card Separator Flap will automatically adjust to slight card thickness variations, a manual adjustment should be made in order for the printer to consistently feed cards which vary from the standard CR-80 .030Ó (.75mm) card thickness. To adjust the Card Separator Flap, refer to the following steps:

1.Open the Card Hopper Door located on the right-hand side of the printer.

2.Remove all but two cards from the Card Hopper.

3.Open the Top Cover of the printer by pressing the Cover Release Button.

4.Remove the ribbon from the printer.

Section 8: Mechanical Adjustments

59

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Page Trademark Acknowledgements Printing HistoryFor Users in Canada For Users in the United StatesFor Users in Taiwan Table of Contents Appendix a Magnetic Stripe Encoding Module Introduction Thank YouHOW Your Card Printer Works Dye-SublimationSpecial Features Resin Thermal TransferSafety Precautions Sicherheitsmaßnahmen Consignes de sécurité Precauciones de seguridad Precauzioni per la Sicurezza Avvertenze AttenzionePrecauções de Segurança Advertências Cuidado4250/4225 Card Printer UserÕs Manual 4250/4225 Card Printer UserÕs Manual 4250/4225 Card Printer UserÕs Manual 4250/4225 Card Printer UserÕs Manual Choosing a Good Location Getting StartedAbout Moisture Condensation Applying Power Unpacking and InspectionIdentifying the Parts On/Cancel Button LCD DisplayOn LED Light Ready LED LightInstalling the Cleaning Roller Extending the Card Output Drawer Ribbons and Cards About RibbonsResin-Only Ribbons for 4250 Dye-Sublimation-Only Ribbons for 4250 onlyDye-Sublimation/Resin Ribbon for 4250 only Loading Ribbon Into the PrinterSupply Take-up About Cards Loading Cards Into the Printer Running the Self Test Self Test Example Actual size Connecting the Printer to Your Computer Using Your 4200 Series Card PrinterIBM-PC Using Your 4200 Series Card Printer Macintosh Installing the Windows Printer Driver Windows 95/98 or Windows NTWindows Installing the 32-BIT Print Spooler for Windows 95/98 4250/4225 Card Printer UserÕs Manual Installing the Macintosh Printer Driver Setting UP the Printer Driver Choosing the Macintosh Printer DriverWindows 95/98 Windows NTAlgebraic Apply Ribbon OverlayBuffer Single Card CalibrateCard Size Color MatchingDisable Printing Dither ModeControls Dye-Sub IntensityImage Placement FargoColorPanel Graphics Panel OnlyMonitor OrientationPicture Controls Print Edge-to-EdgeResin Heat Ribbon SensorRibbon Type Rotate 180 DegreesPrinting a Card 4250/4225 Card Printer UserÕs Manual Using the Print Backgrounder For Macintosh Installing the BackgrounderPrinting with the Backgrounder Backgrounder Status WindowAdmin menu Backgrounder MenusProblems During a Background Print Jobs menuMaintenance Supplies RequiredStandard Printhead Cleaning Cleaning the PRINTER’S Case Expanded Printhead CleaningCleaning the Inside of the Printer Clearing a Card JAM Clearing a Ribbon JAMCleaning the Card Feed Rollers Cleaning the Drive Roller Maintaining the Cleaning Roller 4250/4225 Card Printer UserÕs Manual Mechanical Adjustments Adjusting the Card Input GuidesMechanical Adjustments Adjusting the Internal Card Guide Adjusting the Card Separator FlapCard Separator Adjustment Wheel Troubleshooting Interpreting LCD Display MessagesTOP Line of LCD Message Cause Solution 4250/4225 Card Printer UserÕs Manual TOP Line of LCD Message Cause Solution TOP Line of LCD Message Cause Solution Both Lines of LCD Message Cause Solution Printer beeps just before each ribbon panel is printed General Troubleshooting SuggestionsPrinter doesn’t seem to work at all ’m having problems printing from Windows 95/98 My prints have spots small voids in themPhotos on my ID cards look very pixelated or grainy Printing gets cut off or is not centered on the cardTwo or more cards feed at the same time Can’t get the cards in between the Card Input Guides4250/4225 Card Printer UserÕs Manual Technical Specifications Card TypesWeight Appendix a Magnetic Stripe Encoding Module Magnetic Track OptionsEncoding Mode / Coercivity / Track Selection Magnetic Track Options Encoded Bit DensityCharacter Data Size Character Ascii OffsetISO Track Locations LRC Generation ModeSending Track Information ~1%JULIE ANDERSON623-85-1253? 4250/4225 Card Printer UserÕs Manual Appendix B Interfacing Information IntroductionWire Diagram CENTRONICS-TYPE Parallel InterfaceSignal Description Mini 8-PIN Serial Interface4250/4225 Card Printer UserÕs Manual Appendix C Internal Printer Settings Adjusting the Internal Printer SettingsImage Darkness 00 + Magnetic Offset 00 + SmartCard Offset 00 + RESUME+CANCEL 4250/4225 Card Printer UserÕs Manual Index Background print utility Bar codesLCD display

Card Printer specifications

The FARGO electronic card printer is a standout solution in the world of identification and access control systems, known for its exceptional quality, reliability, and advanced features. Designed to cater to businesses and organizations of all sizes, FARGO printers have become synonymous with secure card issuance, making them an ideal choice for government entities, educational institutions, corporate organizations, and event management.

One of the main features of the FARGO electronic card printer is its ability to produce high-quality, durable cards. Using state-of-the-art dye-sublimation technology, the printer delivers vibrant images and sharp text, ensuring that cards are not only visually appealing but also equipped with excellent durability against wear and tear. The ability to print in both full color and monochrome provides flexibility, allowing users to choose the best option that fits their needs.

The FARGO printer series integrates multiple security features to enhance card protection. Many models come equipped with the latest hardware and software advancements, including holographic overlaminates and UV printing capabilities. These features offer an extra layer of security, making it challenging for counterfeiters to replicate the issued cards, thus ensuring the integrity of the identification process.

Scalability and ease of use are other notable characteristics of the FARGO electronic card printer. It supports a range of card printing volumes, from low to high, making it suitable for various settings. The user-friendly interface, often featuring easy-to-navigate menus and simple installation processes, ensures that even non-technical staff can operate the equipment without extensive training.

Networking capabilities are another significant advantage of FARGO printers. Many models support USB and Ethernet connections, allowing users to connect to multiple devices within an organization easily. This feature facilitates centralized printing and card management, streamlining the card issuance process.

Physical design is also worth mentioning. FARGO printers are constructed with a compact footprint, allowing them to fit seamlessly into office environments without taking up excessive space. The robust casing provides additional protection, ensuring longevity even after extended use.

Overall, the FARGO electronic card printer represents an efficient and effective solution for organizations seeking reliable card printing capabilities. With its combination of advanced technologies, security features, user-friendly design, and excellent output quality, the FARGO printer series remains a popular choice among businesses striving for professionalism and security in their identification processes.
Top Page Image Contents