
Troubleshooting
11.0TROUBLESHOOTING
This section indicates various UPS symptoms a user may encounter and provides a troubleshooting guide in the event the UPS develops a problem. Use the following information to determine whether external factors caused the problem and how to remedy the situation.
11.1UPS Symptoms
The following symptoms indicate the Liebert® GXT3™ is malfunctioning:
•The relative indicators illuminate, indicating the UPS has detected a problem.
•An alarm buzzer sounds, alerting the user that the UPS requires attention.
11.1.1Indicators
In addition to the fault indicator being illuminated, one or more of LED segments of battery level indi- cator will also be illuminated to provide a diagnostic aid to the user, as shown in Figure 26. The descriptions are listed in Table 4.
Figure 26 Battery level indicator
| 
 | 
 | 
 | 
 | 
 | 
 | 
 | 
 | 
 | |
| 
 | 
 | 
 | A | B | C | D | E | 
 | |
| Table 4 | Indicator descriptions | 
 | 
 | 
 | 
 | 
 | |||
| 
 | 
 | 
 | 
 | 
 | 
 | 
 | 
 | ||
| Indicator | 
 | 
 | Diagnosis/Audible alarm | 
 | 
 | 
 | 
 | ||
| 
 | 
 | 
 | 
 | 
 | 
 | ||||
| A - E | 
 | On bypass from output overload  | |||||||
| 
 | 
 | 
 | 
 | 
 | 
 | ||||
| A | 
 | On bypass due to overtemperature condition  | |||||||
| 
 | 
 | 
 | 
 | 
 | 
 | ||||
| B | 
 | On bypass due to DC bus overvoltage  | |||||||
| 
 | 
 | 
 | 
 | 
 | 
 | ||||
| C | 
 | On bypass due to DC/DC power supply failure  | |||||||
| 
 | 
 | 
 | 
 | 
 | 
 | 
 | |||
| D | 
 | PFC failure  | 
 | 
 | 
 | ||||
| 
 | 
 | 
 | 
 | 
 | 
 | ||||
| E | 
 | On bypass due to inverter failure  | |||||||
| 
 | 
 | 
 | 
 | 
 | 
 | ||||
| A&B | 
 | UPS Failure (includes  | |||||||
| 
 | charger failure) and continuous alarm | 
 | 
 | 
 | |||||
| 
 | 
 | 
 | 
 | 
 | |||||
| A&C | 
 | UPS failed battery test  | |||||||
| 
 | 
 | 
 | 
 | 
 | 
 | 
 | |||
| A&D | 
 | Maintance bypass switch on (continuous) | 
 | 
 | 
 | ||||
| 
 | 
 | 
 | 
 | 
 | 
 | ||||
| A&E | 
 | Bypass feedback  | 
 | 
 | |||||
| 
 | 
 | 
 | 
 | 
 | 
 | ||||
| B&C | 
 | REPO (one  | |||||||
| 
 | 
 | 
 | 
 | 
 | 
 | 
 | 
 | 
 | |
| B&E | 
 | Short circuit on the output | 
 | 
 | 
 | 
 | 
 | ||
| 
 | 
 | 
 | 
 | 
 | 
 | ||||
| C&E | 
 | UPS shutdown by command from communication (USB port or Liebert® IntelliSlot® port) (no | |||||||
| 
 | audible) | 
 | 
 | 
 | 
 | 
 | |||
| 
 | 
 | 
 | 
 | 
 | 
 | 
 | |||
| Utility LED flash | 
 | 
 | 
 | 
 | 
 | ||||
| 
 | 
 | 
 | 
 | 
 | |||||
| Battery Indicator | Internal battery source not available (continuous horn); check battery connection, power down | ||||||||
| Flashing | and reboot UPS | 
 | 
 | 
 | 
 | 
 | |||
| Bypass Indicator | Utility power voltage or frequency is out of tolerance; bypass is unavailable | ||||||||
| Flashing | |||||||||
| 
 | 
 | 
 | 
 | 
 | 
 | 
 | |||
| A - E indicators are shown in Figure 26 | 
 | 
 | 
 | 
 | 
 | ||||
35