Cooper Bussmann BU-945U-E 802.11 DSSS user manual DB9 Connector Pinouts, RS485 Serial Port

Page 13

Cooper Bussmann Wireless Ethernet & Device Server BU-945U-E 802.11 DSSS User Manual

DB9 Connector Pinouts

Pin	Name	Direction	Function
1	DCD	Out	Data carrier detect
2	RD	Out	Transmit Data – Serial Data Output (from DCE to DTE)
3	TD	In	Receive Data – Serial Data Input (from DTE to DCE)
4	DTR	In	Data Terminal Ready
5	SG	- -	Signal Ground
6	DSR	Out	Data Set Ready - always high when unit is powered on.
7	RTS	In	Request to Send
8	CTS	Out	Clear to send
9	RI	- -	Ring indicator

RS485 Serial Port

The RS485 port provides for communication between the BU-945U-E unit and its host device using a multi-drop cable. Up to 32 devices may be connected in each multi-drop network.

As the RS485 communication medium is shared, only one of the units on the RS485 cable may send data at any one time. Thus, communication protocols based on the RS-485 standard require some type of arbitration.

RS485 is a balanced, differential standard but it is recommended that shielded, twisted pair cable be used to interconnect modules to reduce potential RFI. It is important to maintain the polarity of the two RS485 wires. An RS485 network should be wired as indicated in the diagram below and terminated at each end of the network with a 120-ohm resistor. On-board 120-ohm resistors are provided and may be engaged by operating the single DIP switch in the end plate next to the RS485 terminals. The DIP switch should be in the “1” or “on” position to connect the resistor. If the module is not at one end of the RS485 cable, the switch should be off.

3A1582Rev1.6

www.cooperbussmann.com/BussmannWirelessResources

13

Image 13

Contents Read Retain FCC Notice Cooper Bussmann Application EngineeringPhone 800 a.m 500 p.m. Central, M-F 636 Fax 636 GNU Free Documentation License Important NoticeCooper Bussmann Contents Access Point vs Client BU-945U-E 802.11 630mW max powerNetwork Topology 3A1582Rev1.6 Bridge vs. Router Getting Started Quickly General Antenna InstallationPlant and Factory Installations Bench test and Demo System SetupLine-of-sight installations AntennasOmni-directional Antennas Installation tipsSerial Connections Power SupplyDirectional Antennas RS232 Serial PortRS485 Serial Port DB9 Connector Pinouts3A1582Rev1.6 Discrete Digital Input/Output Start-up LED Indication Selecting a Channel802.11 900 MHz Channels 3A1582Rev1.6 Data Throughput Based on Repeater Hops Radio ThroughputDefault Configuration Configuring the Unit for the First TimeAccessing Configuration for the First Time Enter the username user and default password user Power up the BU-945U-E moduleMethod 1 Set PC to same network as BU-945U-E For local addresses3A1582Rev1.6 Quick Start Quick Start ConfigurationNetwork Configuration Wireless ports will have the same IP address Dhcp Server Configuration, Default is uncheckedConfigured Essid of the client Save Changes and ResetEncryption keys must not be all zeros, i.e Security Menu3A1582Rev1.6 Normal Operation Radio ConfigurationTransparent Bridge Operation Router OperationSignal quality, etc Bands Default is AutoDrop back to non-bursting mode Access pointRadio Mode BU-945U-E Only Supports the 802.11 Standard Dhcp Client ConfigurationDefault distance is 20km Channel SelectionDNS Server Configuration Dhcp Server ConfigurationSpanning Tree Algorithm / Redundancy Multiple AP Repeater Mesh Network 3A1582Rev1.6 Site B WDS Configuration Example Extending range using WDSExample Adding Redundancy Example Roaming with WDS Access Points3A1582Rev1.6 Example WDS Routed Network Mouse, to highlight the entire row WDS Connections Routing RulesSTP Specifies a destination host Wireless Message FilteringInformation at a later time 3A1582Rev1.6 IP Address Filter Configuration MAC Address Filter ConfigurationUtilize the radio link. All other devices are blocked ARP Filter Configuration RS-232 PPP Server Serial Port ConfigurationSerial Gateway Modbus Modbus RTU to TCP Serial Gateway Server/Client/MulticastSerial Menu Modbus TCP to RTU GatewayMulticast Pipe Manager Port on the Client, i.e., Scada, DCS, etc Digital Input/OutputMulticast Group IP Address To be the same on all communicating Multicast devicesModbus I/O Transfer 3A1582Rev1.6 Modbus TCP Configuration on I/O Transfer Menu Modbus TCP Client Mappings on I/O Transfer Menu Module Information ConfigurationModule Information Webpage Fields System Tools Remote ConfigurationSetting a BU-945U-E to Factory Default Settings Configuration ExamplesExtending a Wired Network Client 2 Configuration Client 1 ConfigurationLAN B Configuration Client Configuration Access Point ConfigurationExtending Range of a Network with a Repeater Hop Boot Status LED Indication during Start-up Diagnostics ChartLED Indicator Condition Meaning RED ContinuouslyConnectivity Diagnostic Information AvailableConnectivity Parameters Site SurveyNetwork Traffic Analysis Statistics9999 Both Reset module enter Ffff to reset module Internal Diagnostic Modbus RegistersConnection Information 5014 STA OnlyStatistic Registers Utilities Testing Radio PathsPing 3A1582Rev1.6 Arp IpconfigRoute General Power SupplyRadio Transceiver Serial PortsInput / Output status System ParametersAppendix a Firmware Upgrades Web-Based UpgradeCSMA/CA ACKCSMA/CD DhcpIPX-SPX IeeeISN NAT SNRNIC SSLVPN VoIPWAN WEPDBm to mW Conversion Materials InstallationIperf Applications 3A1582Rev1.6 JPerf Application 3A1582Rev1.6 Terms and Conditions Preamble3A1582Rev1.6 No Warranty 3A1582Rev1.6 Customer Assistance