Cooper Bussmann BU-945U-E 802.11 DSSS user manual Statistic Registers

Page 61

Cooper Bussmann Wireless Ethernet & Device Server BU-945U-E 802.11 DSSS User Manual

Statistic Registers

Register	Module	Description
4500	Both	Total data packets received on the interface
4502	Both	Received frames with antenna 1 (TX/RX)
4504	Both	Received frames with antenna 2 (RX)
4506	Both	Receiver / default antenna switches
4508	Both	Receive message failed due to bad CRC
4510	Both	Receive message failed due to decryption
4512	Both	Receive message failed due to MIC failure
4514	Both	Receive message failed due to FIFO overrun
4516	Both	Beacon missed interrupts
4518	Both	Total data packet sent on the interface
4520	Both	Transmit frames with antenna 1 (TX/RX)
4522	Both	Transmit frames with antenna 2 (RX)
4524	Both	Transmitter antenna switches
4526	Both	Transmitter on-chip retries
4528	Both	Transmit message failed due to too many retries
4530	Both	Transmit frames with alternate rate
4532	Both	Transmit frames with no ack marked (i.e., broadcast, multicast)
4534	Both	Management frames transmitted
4536	Both	Transmit frames with rts enabled
4538	Both	Transmit frames with cts enabled
4540	Both	Beacons transmitted
4542	Both	Beacon missed count
4544	Both	Beacon miss reset count
4546	Both	Transmit message failed due to no tx buffer (data)
4548	Both	Fatal hardware error interrupts
4550	Both	Receiver PHY error summary count
4552	Both	Transmitter queue stopped because it's full

3A1582Rev1.6

www.cooperbussmann.com/BussmannWirelessResources

61

Image 61

Contents Read Retain FCC Notice Cooper Bussmann Application EngineeringPhone 800 a.m 500 p.m. Central, M-F 636 Fax 636 GNU Free Documentation License Important NoticeCooper Bussmann Contents Access Point vs Client BU-945U-E 802.11 630mW max powerNetwork Topology 3A1582Rev1.6 Bridge vs. Router Getting Started Quickly General Antenna InstallationPlant and Factory Installations Bench test and Demo System SetupLine-of-sight installations AntennasOmni-directional Antennas Installation tipsSerial Connections Power SupplyDirectional Antennas RS232 Serial PortRS485 Serial Port DB9 Connector Pinouts3A1582Rev1.6 Discrete Digital Input/Output Start-up LED Indication Selecting a Channel802.11 900 MHz Channels 3A1582Rev1.6 Data Throughput Based on Repeater Hops Radio ThroughputDefault Configuration Configuring the Unit for the First TimeAccessing Configuration for the First Time Enter the username user and default password user Power up the BU-945U-E moduleMethod 1 Set PC to same network as BU-945U-E For local addresses3A1582Rev1.6 Quick Start Quick Start ConfigurationNetwork Configuration Wireless ports will have the same IP address Dhcp Server Configuration, Default is uncheckedConfigured Essid of the client Save Changes and ResetEncryption keys must not be all zeros, i.e Security Menu3A1582Rev1.6 Normal Operation Radio ConfigurationTransparent Bridge Operation Router OperationSignal quality, etc Bands Default is AutoDrop back to non-bursting mode Access pointRadio Mode BU-945U-E Only Supports the 802.11 Standard Dhcp Client ConfigurationDefault distance is 20km Channel SelectionDNS Server Configuration Dhcp Server ConfigurationSpanning Tree Algorithm / Redundancy Multiple AP Repeater Mesh Network 3A1582Rev1.6 Site B WDS Configuration Example Extending range using WDSExample Adding Redundancy Example Roaming with WDS Access Points3A1582Rev1.6 Example WDS Routed Network Mouse, to highlight the entire row WDS Connections Routing RulesSTP Specifies a destination host Wireless Message FilteringInformation at a later time 3A1582Rev1.6 IP Address Filter Configuration MAC Address Filter ConfigurationUtilize the radio link. All other devices are blocked ARP Filter Configuration RS-232 PPP Server Serial Port ConfigurationSerial Gateway Modbus Modbus RTU to TCP Serial Gateway Server/Client/MulticastSerial Menu Modbus TCP to RTU GatewayMulticast Pipe Manager Port on the Client, i.e., Scada, DCS, etc Digital Input/OutputMulticast Group IP Address To be the same on all communicating Multicast devicesModbus I/O Transfer 3A1582Rev1.6 Modbus TCP Configuration on I/O Transfer Menu Modbus TCP Client Mappings on I/O Transfer Menu Module Information ConfigurationModule Information Webpage Fields System Tools Remote ConfigurationSetting a BU-945U-E to Factory Default Settings Configuration ExamplesExtending a Wired Network Client 2 Configuration Client 1 ConfigurationLAN B Configuration Client Configuration Access Point ConfigurationExtending Range of a Network with a Repeater Hop Boot Status LED Indication during Start-up Diagnostics ChartLED Indicator Condition Meaning RED ContinuouslyConnectivity Diagnostic Information AvailableConnectivity Parameters Site SurveyNetwork Traffic Analysis Statistics9999 Both Reset module enter Ffff to reset module Internal Diagnostic Modbus RegistersConnection Information 5014 STA OnlyStatistic Registers Utilities Testing Radio PathsPing 3A1582Rev1.6 Arp IpconfigRoute General Power SupplyRadio Transceiver Serial PortsInput / Output status System ParametersAppendix a Firmware Upgrades Web-Based UpgradeCSMA/CA ACKCSMA/CD DhcpIPX-SPX IeeeISN NAT SNRNIC SSLVPN VoIPWAN WEPDBm to mW Conversion Materials InstallationIperf Applications 3A1582Rev1.6 JPerf Application 3A1582Rev1.6 Terms and Conditions Preamble3A1582Rev1.6 No Warranty 3A1582Rev1.6 Customer Assistance