Cooper Bussmann BU-945U-E 802.11 DSSS user manual Internal Diagnostic Modbus Registers, STA Only

Page 60

Cooper Bussmann Wireless Ethernet & Device Server BU-945U-E 802.11 DSSS User Manual

4.4 Internal Diagnostic Modbus Registers

There are a number of internal diagnostic registers that can be accessed via Modbus TCP/RTU that will help with analyzing and diagnosing the radio network. To access these register the Modbus Server will need to be enabled and a Modbus Server address will need to be configured (See 3.16 “Modbus I/O Transfer” for details on how this is done).

After enabling the Modbus Client you can then access the following information by reading the corresponding Modbus Address at the Server ID address.

Connection Information

Register	Module	Description
5000	Both	Total number Associated Stations
5001	Both	Current Radio Channel. See section 3.2 “Selecting a Channel” for channel details
5002	Both	Number Wireless Interfaces configured, includes Virtual Interfaces – wi1-wi10
5010	Both	Wireless Adaptor (wi0) - Link Status
5011	Both	Wireless Adaptor (wi0) - Link Status Inverted
5012	Both	Wireless Adaptor (wi0) - Number Associated Stations for this interface
5013	AP Only	Wireless Adaptor (wi0) - Points to the starting register of the AP's Station List. First
		interface (wi0) will always start at 5200 and dynamically enter data depending on the
		number of STA’s. Remaining interfaces (wi1-wi10) will be entered after wi0 data.
		Register 5023, 5033, etc. will indicate starting location for each interface.
5014	STA Only	Wireless Adaptor (wi0) – RSSI & BGND of Rx message from AP e.g. Hex 5F5D = 5F for
		RSSI and 5D for BGND (Convert value from hex to dec and add a “-“ e.g., 5F = -95dB)
5015	STA Only	Wireless Adaptor (wi0) - Transmit Data Rate from the Access Point
5016	STA Only	Wireless Adaptor (wi0) - MAC Address of the Access Point
5020-5026	As per 5010-5016 As per registers 5010-5016 but for the next Wireless Adaptor (wi1)
5030-5036	As per 5010-5016 As per registers 5010-5016 but for the next Wireless Adaptor (wi2)
5040-5046	As per 5010-5016 As per registers 5010-5016 but for the next Wireless Adaptor (wi3)
...etc.	As per 5010-5016 As per registers 5010-5016 but for the next Wireless Adaptor (wi10)
5200	AP Only	RSSI of the Client (STA)
5201	AP Only	Transmit Data Rate to Client (STA)
5202	AP Only	MAC address of Client (STA)
...etc.	AP Only	Dynamic list of STA's Refer to register 5023, 5033, etc. for starting register of each wi interface
9999	Both	Reset module (enter FFFF to reset module)

60

www.cooperbussmann.com/BussmannWirelessResources

3A1582Rev1.6

Image 60

Contents Read Retain Cooper Bussmann Application Engineering FCC NoticePhone 800 a.m 500 p.m. Central, M-F 636 Fax 636 Important Notice GNU Free Documentation LicenseCooper Bussmann Contents BU-945U-E 802.11 630mW max power Access Point vs ClientNetwork Topology 3A1582Rev1.6 Bridge vs. Router Getting Started Quickly Antenna Installation GeneralBench test and Demo System Setup Plant and Factory InstallationsLine-of-sight installations AntennasInstallation tips Omni-directional AntennasPower Supply Serial ConnectionsDirectional Antennas RS232 Serial PortDB9 Connector Pinouts RS485 Serial Port3A1582Rev1.6 Discrete Digital Input/Output Start-up Selecting a Channel LED Indication802.11 900 MHz Channels 3A1582Rev1.6 Radio Throughput Data Throughput Based on Repeater HopsConfiguring the Unit for the First Time Default ConfigurationAccessing Configuration for the First Time Power up the BU-945U-E module Enter the username user and default password userMethod 1 Set PC to same network as BU-945U-E For local addresses3A1582Rev1.6 Quick Start Configuration Quick StartNetwork Configuration Dhcp Server Configuration, Default is unchecked Wireless ports will have the same IP addressConfigured Essid of the client Save Changes and ResetSecurity Menu Encryption keys must not be all zeros, i.e3A1582Rev1.6 Radio Configuration Normal OperationTransparent Bridge Operation Router OperationBands Default is Auto Signal quality, etcDrop back to non-bursting mode Access pointDhcp Client Configuration Radio Mode BU-945U-E Only Supports the 802.11 StandardDefault distance is 20km Channel SelectionDhcp Server Configuration DNS Server ConfigurationSpanning Tree Algorithm / Redundancy Multiple AP Repeater Mesh Network 3A1582Rev1.6 Example Extending range using WDS Site B WDS ConfigurationExample Roaming with WDS Access Points Example Adding Redundancy3A1582Rev1.6 Example WDS Routed Network Mouse, to highlight the entire row Routing Rules WDS ConnectionsSTP Wireless Message Filtering Specifies a destination hostInformation at a later time 3A1582Rev1.6 MAC Address Filter Configuration IP Address Filter ConfigurationUtilize the radio link. All other devices are blocked ARP Filter Configuration Serial Port Configuration RS-232 PPP ServerSerial Gateway Server/Client/Multicast Serial Gateway Modbus Modbus RTU to TCPModbus TCP to RTU Gateway Serial MenuMulticast Pipe Manager Digital Input/Output Port on the Client, i.e., Scada, DCS, etcMulticast Group IP Address To be the same on all communicating Multicast devicesModbus I/O Transfer 3A1582Rev1.6 Modbus TCP Configuration on I/O Transfer Menu Module Information Configuration Modbus TCP Client Mappings on I/O Transfer MenuModule Information Webpage Fields Remote Configuration System ToolsConfiguration Examples Setting a BU-945U-E to Factory Default SettingsExtending a Wired Network Client 1 Configuration Client 2 ConfigurationLAN B Configuration Access Point Configuration Client ConfigurationExtending Range of a Network with a Repeater Hop Diagnostics Chart Boot Status LED Indication during Start-upLED Indicator Condition Meaning RED ContinuouslyDiagnostic Information Available ConnectivityConnectivity Parameters Site SurveyStatistics Network Traffic AnalysisInternal Diagnostic Modbus Registers 9999 Both Reset module enter Ffff to reset moduleConnection Information 5014 STA OnlyStatistic Registers Testing Radio Paths UtilitiesPing 3A1582Rev1.6 Ipconfig ArpRoute Power Supply GeneralRadio Transceiver Serial PortsSystem Parameters Input / Output statusWeb-Based Upgrade Appendix a Firmware UpgradesACK CSMA/CACSMA/CD DhcpIeee IPX-SPXISN SNR NATNIC SSLVoIP VPNWAN WEPDBm to mW Conversion Installation MaterialsIperf Applications 3A1582Rev1.6 JPerf Application 3A1582Rev1.6 Preamble Terms and Conditions3A1582Rev1.6 No Warranty 3A1582Rev1.6 Customer Assistance