Cooper Bussmann BU-945U-E 802.11 DSSS user manual Access Point Configuration, Client Configuration

Page 56

Cooper Bussmann Wireless Ethernet & Device Server BU-945U-E 802.11 DSSS User Manual

Access Point Configuration

•Connect straight through Ethernet cable between PC and BU-945U-E

•Ensure configuration PC and BU-945U-E are setup to communicate on the same network

•Set DIP switch to SETUP

•Power up unit, and wait for LINK led to cease flashing

•Adjust PC network settings

•Set Configuration PC network card with network setting of IP address 192.168.0.1, netmask 255.255.255.0

•Open configuration webpage with Internet Explorer at address 192.168.0.1XX/

•When prompted for password, enter default username “user” and password “user”

•Enter “Network,” and select Operating Mode as Access Point

•Device Mode should be set to Router

•Set the Gateway IP address to 192.168.0.1

•Set the Ethernet IP address to 192.168.0.200, network mask 255.255.255.0

•Set the Wireless IP address to 169.254.102.54, network mask 255.255.255.0

•Select the Radio Encryption required, and enter encryption keys or passphrase if necessary

•Set DIP switch to RUN

•Click on button Save to Flash and Reset. Webpage will display that message indicating details are being written to flash. Wait for BU-945U-E to reboot before removing power. Enter a System Generator String.

Client Configuration

Perform the same configuration steps as the Access Point configuration with the following differences:

•Enter “Network,” and select Operating Mode as Client

•Device Mode should be set to Bridge

•Set the Gateway IP address to 169.254.102.54

•Set the Ethernet IP address to 169.254.102.53, network mask 255.255.255.0

•Set the Wireless IP address to 169.254.102.53, network mask 255.255.255.0

•Click on button Save to Flash and Reset. Webpage will display that message indicating details are being written to flash. Wait for BU-945U-E to reboot before removing power.

Extending Range of a Network with a Repeater Hop

Configure units as described in the “Extending a wired network” example above. Place the Access Point at the remote intermediate repeater location. Additional repeaters can be added using Wireless Distribution System (WDS) – refer section 3.11 ”Multiple AP Repeater Mesh Network” for further details.

56

www.cooperbussmann.com/BussmannWirelessResources

3A1582Rev1.6

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Read Retain Phone 800 a.m 500 p.m. Central, M-F 636 Fax 636 Cooper Bussmann Application EngineeringFCC Notice Cooper Bussmann Important NoticeGNU Free Documentation License Contents Network Topology BU-945U-E 802.11 630mW max powerAccess Point vs Client 3A1582Rev1.6 Bridge vs. Router Getting Started Quickly Antenna Installation GeneralBench test and Demo System Setup Plant and Factory InstallationsLine-of-sight installations AntennasInstallation tips Omni-directional AntennasPower Supply Serial ConnectionsDirectional Antennas RS232 Serial PortDB9 Connector Pinouts RS485 Serial Port3A1582Rev1.6 Discrete Digital Input/Output Start-up 802.11 900 MHz Channels Selecting a ChannelLED Indication 3A1582Rev1.6 Radio Throughput Data Throughput Based on Repeater HopsAccessing Configuration for the First Time Configuring the Unit for the First TimeDefault Configuration Power up the BU-945U-E module Enter the username user and default password userMethod 1 Set PC to same network as BU-945U-E For local addresses3A1582Rev1.6 Quick Start Configuration Quick StartNetwork Configuration Dhcp Server Configuration, Default is unchecked Wireless ports will have the same IP addressConfigured Essid of the client Save Changes and ResetSecurity Menu Encryption keys must not be all zeros, i.e3A1582Rev1.6 Radio Configuration Normal OperationTransparent Bridge Operation Router OperationBands Default is Auto Signal quality, etcDrop back to non-bursting mode Access pointDhcp Client Configuration Radio Mode BU-945U-E Only Supports the 802.11 StandardDefault distance is 20km Channel SelectionSpanning Tree Algorithm / Redundancy Dhcp Server ConfigurationDNS Server Configuration Multiple AP Repeater Mesh Network 3A1582Rev1.6 Example Extending range using WDS Site B WDS ConfigurationExample Roaming with WDS Access Points Example Adding Redundancy3A1582Rev1.6 Example WDS Routed Network Mouse, to highlight the entire row STP Routing RulesWDS Connections Information at a later time Wireless Message FilteringSpecifies a destination host 3A1582Rev1.6 Utilize the radio link. All other devices are blocked MAC Address Filter ConfigurationIP Address Filter Configuration ARP Filter Configuration Serial Port Configuration RS-232 PPP ServerSerial Gateway Server/Client/Multicast Serial Gateway Modbus Modbus RTU to TCPModbus TCP to RTU Gateway Serial MenuMulticast Pipe Manager Digital Input/Output Port on the Client, i.e., Scada, DCS, etcMulticast Group IP Address To be the same on all communicating Multicast devicesModbus I/O Transfer 3A1582Rev1.6 Modbus TCP Configuration on I/O Transfer Menu Module Information Webpage Fields Module Information ConfigurationModbus TCP Client Mappings on I/O Transfer Menu Remote Configuration System ToolsExtending a Wired Network Configuration ExamplesSetting a BU-945U-E to Factory Default Settings LAN B Configuration Client 1 ConfigurationClient 2 Configuration Extending Range of a Network with a Repeater Hop Access Point ConfigurationClient Configuration Diagnostics Chart Boot Status LED Indication during Start-upLED Indicator Condition Meaning RED ContinuouslyDiagnostic Information Available ConnectivityConnectivity Parameters Site SurveyStatistics Network Traffic AnalysisInternal Diagnostic Modbus Registers 9999 Both Reset module enter Ffff to reset moduleConnection Information 5014 STA OnlyStatistic Registers Ping Testing Radio PathsUtilities 3A1582Rev1.6 Ipconfig ArpRoute Power Supply GeneralRadio Transceiver Serial PortsSystem Parameters Input / Output statusWeb-Based Upgrade Appendix a Firmware UpgradesACK CSMA/CACSMA/CD DhcpISN IeeeIPX-SPX SNR NATNIC SSLVoIP VPNWAN WEPDBm to mW Conversion Iperf Applications InstallationMaterials 3A1582Rev1.6 JPerf Application 3A1582Rev1.6 Preamble Terms and Conditions3A1582Rev1.6 No Warranty 3A1582Rev1.6 Customer Assistance
Top Page Image Contents