Cooper Bussmann BU-945U-E 802.11 DSSS user manual Method 1 Set PC to same network as BU-945U-E

Page 21

Cooper Bussmann Wireless Ethernet & Device Server BU-945U-E 802.11 DSSS User Manual

Method 1 - Set PC to same network as BU-945U-E

Connect the Ethernet cable between unit and the PC configuring the module.

•Set the Factory Default Switch to the SETUP position. This will always start the BU-945U-E with Ethernet IP address 192.168.0.1XX, subnet mask 255.255.255.0, gateway IP 192.168.0.1 and the radio disabled. Do not forget to set the switch back to the RUN position and restart the module at the conclusion of configuration for resumption of normal operation.

•Power up the BU-945U-E module.

•Open “Network Settings” on your PC under Control Panel. The following description is for Windows XP - earlier Windows operating systems have similar settings.

•Open “Properties” of Local Area Connection.

•Select Internet Protocol (TCP/IP) and click on Properties.

•On the General tab enter IP address 192.168.0.1, Subnet mask 255.255.255.0 and press “OK”

•Open Internet Explorer and ensure that settings will allow you to connect to the IP address selected. If the PC uses a proxy server, ensure that Internet Explorer will bypass the Proxy Server for local addresses.

•This option may be modified by opening Tools -> Internet Options - > Connections Tab -> LAN Settings->Proxy Server -> bypass proxy

for local addresses.

•Enter the default IP address for the BU-945U-E 192.168.0.1XX where XX is the last two digits of the serial number.

•Enter the username “user” and default password “user.”

Figure 1

3A1582Rev1.6

www.cooperbussmann.com/BussmannWirelessResources

21

Image 21

Contents Read Retain Cooper Bussmann Application Engineering FCC NoticePhone 800 a.m 500 p.m. Central, M-F 636 Fax 636 Important Notice GNU Free Documentation LicenseCooper Bussmann Contents BU-945U-E 802.11 630mW max power Access Point vs ClientNetwork Topology 3A1582Rev1.6 Bridge vs. Router Getting Started Quickly General Antenna InstallationPlant and Factory Installations Bench test and Demo System SetupLine-of-sight installations AntennasOmni-directional Antennas Installation tipsSerial Connections Power SupplyDirectional Antennas RS232 Serial PortRS485 Serial Port DB9 Connector Pinouts3A1582Rev1.6 Discrete Digital Input/Output Start-up Selecting a Channel LED Indication802.11 900 MHz Channels 3A1582Rev1.6 Data Throughput Based on Repeater Hops Radio ThroughputConfiguring the Unit for the First Time Default ConfigurationAccessing Configuration for the First Time Enter the username user and default password user Power up the BU-945U-E moduleMethod 1 Set PC to same network as BU-945U-E For local addresses3A1582Rev1.6 Quick Start Quick Start ConfigurationNetwork Configuration Wireless ports will have the same IP address Dhcp Server Configuration, Default is uncheckedConfigured Essid of the client Save Changes and ResetEncryption keys must not be all zeros, i.e Security Menu3A1582Rev1.6 Normal Operation Radio ConfigurationTransparent Bridge Operation Router OperationSignal quality, etc Bands Default is AutoDrop back to non-bursting mode Access pointRadio Mode BU-945U-E Only Supports the 802.11 Standard Dhcp Client ConfigurationDefault distance is 20km Channel SelectionDhcp Server Configuration DNS Server ConfigurationSpanning Tree Algorithm / Redundancy Multiple AP Repeater Mesh Network 3A1582Rev1.6 Site B WDS Configuration Example Extending range using WDSExample Adding Redundancy Example Roaming with WDS Access Points3A1582Rev1.6 Example WDS Routed Network Mouse, to highlight the entire row Routing Rules WDS ConnectionsSTP Wireless Message Filtering Specifies a destination hostInformation at a later time 3A1582Rev1.6 MAC Address Filter Configuration IP Address Filter ConfigurationUtilize the radio link. All other devices are blocked ARP Filter Configuration RS-232 PPP Server Serial Port ConfigurationSerial Gateway Modbus Modbus RTU to TCP Serial Gateway Server/Client/MulticastSerial Menu Modbus TCP to RTU GatewayMulticast Pipe Manager Port on the Client, i.e., Scada, DCS, etc Digital Input/OutputMulticast Group IP Address To be the same on all communicating Multicast devicesModbus I/O Transfer 3A1582Rev1.6 Modbus TCP Configuration on I/O Transfer Menu Module Information Configuration Modbus TCP Client Mappings on I/O Transfer MenuModule Information Webpage Fields System Tools Remote ConfigurationConfiguration Examples Setting a BU-945U-E to Factory Default SettingsExtending a Wired Network Client 1 Configuration Client 2 ConfigurationLAN B Configuration Access Point Configuration Client ConfigurationExtending Range of a Network with a Repeater Hop Boot Status LED Indication during Start-up Diagnostics ChartLED Indicator Condition Meaning RED ContinuouslyConnectivity Diagnostic Information AvailableConnectivity Parameters Site SurveyNetwork Traffic Analysis Statistics9999 Both Reset module enter Ffff to reset module Internal Diagnostic Modbus RegistersConnection Information 5014 STA OnlyStatistic Registers Testing Radio Paths UtilitiesPing 3A1582Rev1.6 Arp IpconfigRoute General Power SupplyRadio Transceiver Serial PortsInput / Output status System ParametersAppendix a Firmware Upgrades Web-Based UpgradeCSMA/CA ACKCSMA/CD DhcpIeee IPX-SPXISN NAT SNRNIC SSLVPN VoIPWAN WEPDBm to mW Conversion Installation MaterialsIperf Applications 3A1582Rev1.6 JPerf Application 3A1582Rev1.6 Terms and Conditions Preamble3A1582Rev1.6 No Warranty 3A1582Rev1.6 Customer Assistance