Cooper Bussmann BU-945U-E 802.11 DSSS user manual Discrete Digital Input/Output

Page 15

Cooper Bussmann Wireless Ethernet & Device Server BU-945U-E 802.11 DSSS User Manual

2.5 Discrete (Digital) Input/Output

The BU-945U-E has one on-board discrete/digital I/O channel. This channel can act as either a discrete input or discrete output. It can be monitored, or set remotely, or alternatively used to output a communications alarm status.

If used as an “input”, the I/O channel is suitable for voltage free contacts (such as mechanical switches) or NPN transistor devices (such as electronic proximity switches). PNP transistor devices are not suitable. Contact wetting current of approximately 5mA is provided to maintain reliable operation of driving relays.

The digital input is connected between the "DIO" terminal and common “COM.” The I/O circuit includes a LED indicator which is lit GREEN when the digital input is active, that is, when the input circuit is closed. Provided the resistance of the switching device is less than 200 ohms, the device will be able to activate the digital input.

The I/O channel may also be used as a discrete output. The digital outputs are transistor switched DC signals, FET output to common rated at 30Vdc 500 mA.

The output circuit is connected to the "DIO" terminal. The digital output circuit includes a LED indicator which is lit RED when the digital output is active.

3A1582Rev1.6

www.cooperbussmann.com/BussmannWirelessResources

15

Image 15

Contents Read Retain Cooper Bussmann Application Engineering FCC NoticePhone 800 a.m 500 p.m. Central, M-F 636 Fax 636 Important Notice GNU Free Documentation LicenseCooper Bussmann Contents BU-945U-E 802.11 630mW max power Access Point vs ClientNetwork Topology 3A1582Rev1.6 Bridge vs. Router Getting Started Quickly General Antenna InstallationAntennas Bench test and Demo System SetupPlant and Factory Installations Line-of-sight installationsOmni-directional Antennas Installation tipsRS232 Serial Port Power SupplySerial Connections Directional AntennasRS485 Serial Port DB9 Connector Pinouts3A1582Rev1.6 Discrete Digital Input/Output Start-up Selecting a Channel LED Indication802.11 900 MHz Channels 3A1582Rev1.6 Data Throughput Based on Repeater Hops Radio ThroughputConfiguring the Unit for the First Time Default ConfigurationAccessing Configuration for the First Time For local addresses Power up the BU-945U-E moduleEnter the username user and default password user Method 1 Set PC to same network as BU-945U-E3A1582Rev1.6 Quick Start Quick Start ConfigurationNetwork Configuration Save Changes and Reset Dhcp Server Configuration, Default is uncheckedWireless ports will have the same IP address Configured Essid of the clientEncryption keys must not be all zeros, i.e Security Menu3A1582Rev1.6 Router Operation Radio ConfigurationNormal Operation Transparent Bridge OperationAccess point Bands Default is AutoSignal quality, etc Drop back to non-bursting modeChannel Selection Dhcp Client ConfigurationRadio Mode BU-945U-E Only Supports the 802.11 Standard Default distance is 20kmDhcp Server Configuration DNS Server ConfigurationSpanning Tree Algorithm / Redundancy Multiple AP Repeater Mesh Network 3A1582Rev1.6 Site B WDS Configuration Example Extending range using WDSExample Adding Redundancy Example Roaming with WDS Access Points3A1582Rev1.6 Example WDS Routed Network Mouse, to highlight the entire row Routing Rules WDS ConnectionsSTP Wireless Message Filtering Specifies a destination hostInformation at a later time 3A1582Rev1.6 MAC Address Filter Configuration IP Address Filter ConfigurationUtilize the radio link. All other devices are blocked ARP Filter Configuration RS-232 PPP Server Serial Port ConfigurationSerial Gateway Modbus Modbus RTU to TCP Serial Gateway Server/Client/MulticastSerial Menu Modbus TCP to RTU GatewayMulticast Pipe Manager To be the same on all communicating Multicast devices Digital Input/OutputPort on the Client, i.e., Scada, DCS, etc Multicast Group IP AddressModbus I/O Transfer 3A1582Rev1.6 Modbus TCP Configuration on I/O Transfer Menu Module Information Configuration Modbus TCP Client Mappings on I/O Transfer MenuModule Information Webpage Fields System Tools Remote ConfigurationConfiguration Examples Setting a BU-945U-E to Factory Default SettingsExtending a Wired Network Client 1 Configuration Client 2 ConfigurationLAN B Configuration Access Point Configuration Client ConfigurationExtending Range of a Network with a Repeater Hop RED Continuously Diagnostics ChartBoot Status LED Indication during Start-up LED Indicator Condition MeaningSite Survey Diagnostic Information AvailableConnectivity Connectivity ParametersNetwork Traffic Analysis Statistics5014 STA Only Internal Diagnostic Modbus Registers9999 Both Reset module enter Ffff to reset module Connection InformationStatistic Registers Testing Radio Paths UtilitiesPing 3A1582Rev1.6 Arp IpconfigRoute Serial Ports Power SupplyGeneral Radio TransceiverInput / Output status System ParametersAppendix a Firmware Upgrades Web-Based UpgradeDhcp ACKCSMA/CA CSMA/CDIeee IPX-SPXISN SSL SNRNAT NICWEP VoIPVPN WANDBm to mW Conversion Installation MaterialsIperf Applications 3A1582Rev1.6 JPerf Application 3A1582Rev1.6 Terms and Conditions Preamble3A1582Rev1.6 No Warranty 3A1582Rev1.6 Customer Assistance