Cooper Bussmann BU-945U-E 802.11 DSSS user manual Getting Started Quickly

Page 8

Cooper Bussmann Wireless Ethernet & Device Server BU-945U-E 802.11 DSSS User Manual

1.2 Getting Started Quickly

Most applications for the BU-945U-E require little configuration. The BU-945U-E has many sophisticated features, however if you don’t require these features, this section will allow you to configure the units quickly.

First, read Chapter 2, “Installation.” The BU-945U-E requires an antenna and a power supply.

•Power the BU-945U-E and make an Ethernet connection to your PC (for further information on how to do this, refer to section 3.3 “Configuring the Unit for the first time”)

•Set the BU-945U-E address settings as per section 3.3 “ Configuring the Unit for the first time”

•Save the configuration - the BU-945U-E is now ready to use.

Before installing the BU-945U-E, bench test the system. It is a lot easier to locate problems when the equipment is all together.

There are other configuration settings, which may or may not improve the operation of the system. For details on these settings, refer to section 3.1 “Start-up.”

8

www.cooperbussmann.com/BussmannWirelessResources

3A1582Rev1.6

Image 8

Contents Read Retain Phone 800 a.m 500 p.m. Central, M-F 636 Fax 636 Cooper Bussmann Application EngineeringFCC Notice Cooper Bussmann Important NoticeGNU Free Documentation License Contents Network Topology BU-945U-E 802.11 630mW max powerAccess Point vs Client 3A1582Rev1.6 Bridge vs. Router Getting Started Quickly Antenna Installation GeneralBench test and Demo System Setup Plant and Factory InstallationsLine-of-sight installations AntennasInstallation tips Omni-directional AntennasPower Supply Serial ConnectionsDirectional Antennas RS232 Serial PortDB9 Connector Pinouts RS485 Serial Port3A1582Rev1.6 Discrete Digital Input/Output Start-up 802.11 900 MHz Channels Selecting a ChannelLED Indication 3A1582Rev1.6 Radio Throughput Data Throughput Based on Repeater HopsAccessing Configuration for the First Time Configuring the Unit for the First TimeDefault Configuration Power up the BU-945U-E module Enter the username user and default password userMethod 1 Set PC to same network as BU-945U-E For local addresses3A1582Rev1.6 Quick Start Configuration Quick StartNetwork Configuration Dhcp Server Configuration, Default is unchecked Wireless ports will have the same IP addressConfigured Essid of the client Save Changes and ResetSecurity Menu Encryption keys must not be all zeros, i.e3A1582Rev1.6 Radio Configuration Normal OperationTransparent Bridge Operation Router OperationBands Default is Auto Signal quality, etcDrop back to non-bursting mode Access pointDhcp Client Configuration Radio Mode BU-945U-E Only Supports the 802.11 StandardDefault distance is 20km Channel SelectionSpanning Tree Algorithm / Redundancy Dhcp Server ConfigurationDNS Server Configuration Multiple AP Repeater Mesh Network 3A1582Rev1.6 Example Extending range using WDS Site B WDS ConfigurationExample Roaming with WDS Access Points Example Adding Redundancy3A1582Rev1.6 Example WDS Routed Network Mouse, to highlight the entire row STP Routing RulesWDS Connections Information at a later time Wireless Message FilteringSpecifies a destination host 3A1582Rev1.6 Utilize the radio link. All other devices are blocked MAC Address Filter ConfigurationIP Address Filter Configuration ARP Filter Configuration Serial Port Configuration RS-232 PPP ServerSerial Gateway Server/Client/Multicast Serial Gateway Modbus Modbus RTU to TCPModbus TCP to RTU Gateway Serial MenuMulticast Pipe Manager Digital Input/Output Port on the Client, i.e., Scada, DCS, etcMulticast Group IP Address To be the same on all communicating Multicast devicesModbus I/O Transfer 3A1582Rev1.6 Modbus TCP Configuration on I/O Transfer Menu Module Information Webpage Fields Module Information ConfigurationModbus TCP Client Mappings on I/O Transfer Menu Remote Configuration System ToolsExtending a Wired Network Configuration ExamplesSetting a BU-945U-E to Factory Default Settings LAN B Configuration Client 1 ConfigurationClient 2 Configuration Extending Range of a Network with a Repeater Hop Access Point ConfigurationClient Configuration Diagnostics Chart Boot Status LED Indication during Start-upLED Indicator Condition Meaning RED ContinuouslyDiagnostic Information Available ConnectivityConnectivity Parameters Site SurveyStatistics Network Traffic AnalysisInternal Diagnostic Modbus Registers 9999 Both Reset module enter Ffff to reset moduleConnection Information 5014 STA OnlyStatistic Registers Ping Testing Radio PathsUtilities 3A1582Rev1.6 Ipconfig ArpRoute Power Supply GeneralRadio Transceiver Serial PortsSystem Parameters Input / Output statusWeb-Based Upgrade Appendix a Firmware UpgradesACK CSMA/CACSMA/CD DhcpISN IeeeIPX-SPX SNR NATNIC SSLVoIP VPNWAN WEPDBm to mW Conversion Iperf Applications InstallationMaterials 3A1582Rev1.6 JPerf Application 3A1582Rev1.6 Preamble Terms and Conditions3A1582Rev1.6 No Warranty 3A1582Rev1.6 Customer Assistance