Cooper Bussmann BU-945U-E 802.11 DSSS Cooper Bussmann Application Engineering, FCC Notice

Page 2

Cooper Bussmann Wireless Ethernet & Device Server BU-945U-E 802.11 DSSS User Manual

Cooper Bussmann Application Engineering

•Phone 8:00 a.m - 5:00 p.m. Central, M-F (636) 527-1270

•Fax: (636) 527-1607

•E-mail:FuseTech@cooperindustries.com

Thank you for your selection of the BU-945U-E Wireless Ethernet Modem. We trust it will give you many years of valuable service.

ATTENTION!

Incorrect termination of supply wires may cause internal damage and will void warranty. To ensure your BU-945U-E enjoys a long life.

Double check ALL connections with the user manual before turning the power on.

CAUTION:

To comply with FCC RF Exposure requirements in section 1.1310 of the FCC Rules, antennas used with this device must be installed to provide a separation distance of at least 20cm from all persons to satisfy RF exposure compliance.

DO NOT:

•Operate the transmitter when someone is within 20cm of the antenna

•Operate the transmitter unless all RF connectors are secure and any open connectors are properly terminated.

•Operate the equipment near electrical blasting caps or in an explosive atmosphere

All equipment must be properly grounded for safe operations. All equipment should be serviced only by a qualified technician.

FCC Notice:

This device complies with Part 15.247 of the FCC Rules.

Operation is subject to the following two conditions:

1)This device may not cause harmful interference and

2)This device must accept any interference received, including interference that may cause undesired operation.

This device must be operated as supplied by Cooper Bussmann. Any changes or modifications made to the device without the written consent of Cooper Bussmann may void the user’s authority to operate the device.

End user products that have this device embedded must be installed by experienced radio and antenna personnel, or supplied with non-standard antenna connectors, and antennas available from vendors specified by Cooper Bussmann. Please contact Cooper Bussmann for end user antenna and connector recommendations.

Notices: Safety

Exposure to RF energy is an important safety consideration. The FCC has adopted a safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated equipment as a result of its actions in Docket 93-62 and OET Bulletin 65 Edition 97-01.

FCC Notice:

•Part 15 – This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC rules (Code of Federal Regulations 47CFR Part 15). Operation is subject to the condition that this device does not cause harmful interference.

•Notice any changes or modifications not expressly approved by Cooper Bussmann could void the user’s authority to operate this equipment.

This Device should only be connected to PCs that are covered by either FCC DoC or are FCC certified.

2

www.cooperbussmann.com/BussmannWirelessResources

3A1582Rev1.6

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Read Retain Phone 800 a.m 500 p.m. Central, M-F 636 Fax 636 Cooper Bussmann Application EngineeringFCC Notice Cooper Bussmann Important NoticeGNU Free Documentation License Contents Network Topology BU-945U-E 802.11 630mW max powerAccess Point vs Client 3A1582Rev1.6 Bridge vs. Router Getting Started Quickly Antenna Installation GeneralLine-of-sight installations Bench test and Demo System SetupPlant and Factory Installations AntennasInstallation tips Omni-directional AntennasDirectional Antennas Power SupplySerial Connections RS232 Serial PortDB9 Connector Pinouts RS485 Serial Port3A1582Rev1.6 Discrete Digital Input/Output Start-up 802.11 900 MHz Channels Selecting a ChannelLED Indication 3A1582Rev1.6 Radio Throughput Data Throughput Based on Repeater HopsAccessing Configuration for the First Time Configuring the Unit for the First TimeDefault Configuration Method 1 Set PC to same network as BU-945U-E Power up the BU-945U-E moduleEnter the username user and default password user For local addresses3A1582Rev1.6 Quick Start Configuration Quick StartNetwork Configuration Configured Essid of the client Dhcp Server Configuration, Default is uncheckedWireless ports will have the same IP address Save Changes and ResetSecurity Menu Encryption keys must not be all zeros, i.e3A1582Rev1.6 Transparent Bridge Operation Radio ConfigurationNormal Operation Router OperationDrop back to non-bursting mode Bands Default is AutoSignal quality, etc Access pointDefault distance is 20km Dhcp Client ConfigurationRadio Mode BU-945U-E Only Supports the 802.11 Standard Channel SelectionSpanning Tree Algorithm / Redundancy Dhcp Server ConfigurationDNS Server Configuration Multiple AP Repeater Mesh Network 3A1582Rev1.6 Example Extending range using WDS Site B WDS ConfigurationExample Roaming with WDS Access Points Example Adding Redundancy3A1582Rev1.6 Example WDS Routed Network Mouse, to highlight the entire row STP Routing RulesWDS Connections Information at a later time Wireless Message FilteringSpecifies a destination host 3A1582Rev1.6 Utilize the radio link. All other devices are blocked MAC Address Filter ConfigurationIP Address Filter Configuration ARP Filter Configuration Serial Port Configuration RS-232 PPP ServerSerial Gateway Server/Client/Multicast Serial Gateway Modbus Modbus RTU to TCPModbus TCP to RTU Gateway Serial MenuMulticast Pipe Manager Multicast Group IP Address Digital Input/OutputPort on the Client, i.e., Scada, DCS, etc To be the same on all communicating Multicast devicesModbus I/O Transfer 3A1582Rev1.6 Modbus TCP Configuration on I/O Transfer Menu Module Information Webpage Fields Module Information ConfigurationModbus TCP Client Mappings on I/O Transfer Menu Remote Configuration System ToolsExtending a Wired Network Configuration ExamplesSetting a BU-945U-E to Factory Default Settings LAN B Configuration Client 1 ConfigurationClient 2 Configuration Extending Range of a Network with a Repeater Hop Access Point ConfigurationClient Configuration LED Indicator Condition Meaning Diagnostics ChartBoot Status LED Indication during Start-up RED ContinuouslyConnectivity Parameters Diagnostic Information AvailableConnectivity Site SurveyStatistics Network Traffic AnalysisConnection Information Internal Diagnostic Modbus Registers9999 Both Reset module enter Ffff to reset module 5014 STA OnlyStatistic Registers Ping Testing Radio PathsUtilities 3A1582Rev1.6 Ipconfig ArpRoute Radio Transceiver Power SupplyGeneral Serial PortsSystem Parameters Input / Output statusWeb-Based Upgrade Appendix a Firmware UpgradesCSMA/CD ACKCSMA/CA DhcpISN IeeeIPX-SPX NIC SNRNAT SSLWAN VoIPVPN WEPDBm to mW Conversion Iperf Applications InstallationMaterials 3A1582Rev1.6 JPerf Application 3A1582Rev1.6 Preamble Terms and Conditions3A1582Rev1.6 No Warranty 3A1582Rev1.6 Customer Assistance
Top Page Image Contents