Cooper Bussmann BU-945U-E 802.11 DSSS Configuration Examples, Extending a Wired Network

Page 54

Cooper Bussmann Wireless Ethernet & Device Server BU-945U-E 802.11 DSSS User Manual

3.21 Configuration Examples

Setting a BU-945U-E to Factory Default Settings

Access configuration webpage on the BU-945U-E. Refer section”3.3.”

Click on “System Tools” Menu Item

Click on Factory Default Configuration Reset, and wait for unit to reset. While the module executes the reset sequence the OK LED will flash. The OK LED will turn green when the reset sequence is complete.

Extending a Wired Network

Access Point Configuration

Connect straight through Ethernet cable between PC and BU-945U-E.

Ensure configuration PC and BU-945U-E are setup to communicate on the same network

Set DIP switch to SETUP mode.

Power up unit, and wait for the OK LED to cease flashing.

Adjust PC network settings

Set Configuration PC network card with network setting of IP address 192.168.0.1, netmask 255.255.255.0

Open configuration webpage with Internet Explorer at address 192.168.0.1XX/ where XX is the last two digits of the module’s serial number

When prompted for password, enter default username “user” and password “user”

Click “Network”, and select Operating Mode as Access Point.

Select Device Mode as Bridge.

Change the Gateway IP Address to 192.168.0.1

Change the Ethernet and Wireless IP addresses to 192.168.0.200

Change Ethernet and Wireless Subnet masks to 255.255.255.0

Enter a System Address (ESSID) string

Select the Radio Encryption required.

Set DIP switch to RUN

Save the changes and unit will restart with new settings.

54

www.cooperbussmann.com/BussmannWirelessResources

3A1582Rev1.6

Image 54
Contents Read Retain Cooper Bussmann Application Engineering FCC NoticePhone 800 a.m 500 p.m. Central, M-F 636 Fax 636 Important Notice GNU Free Documentation LicenseCooper Bussmann Contents BU-945U-E 802.11 630mW max power Access Point vs ClientNetwork Topology 3A1582Rev1.6 Bridge vs. Router Getting Started Quickly Antenna Installation GeneralLine-of-sight installations Bench test and Demo System SetupPlant and Factory Installations AntennasInstallation tips Omni-directional AntennasDirectional Antennas Power SupplySerial Connections RS232 Serial PortDB9 Connector Pinouts RS485 Serial Port3A1582Rev1.6 Discrete Digital Input/Output Start-up Selecting a Channel LED Indication802.11 900 MHz Channels 3A1582Rev1.6 Radio Throughput Data Throughput Based on Repeater HopsConfiguring the Unit for the First Time Default ConfigurationAccessing Configuration for the First Time Method 1 Set PC to same network as BU-945U-E Power up the BU-945U-E moduleEnter the username user and default password user For local addresses3A1582Rev1.6 Quick Start Configuration Quick StartNetwork Configuration Configured Essid of the client Dhcp Server Configuration, Default is uncheckedWireless ports will have the same IP address Save Changes and ResetSecurity Menu Encryption keys must not be all zeros, i.e3A1582Rev1.6 Transparent Bridge Operation Radio ConfigurationNormal Operation Router OperationDrop back to non-bursting mode Bands Default is AutoSignal quality, etc Access pointDefault distance is 20km Dhcp Client ConfigurationRadio Mode BU-945U-E Only Supports the 802.11 Standard Channel SelectionDhcp Server Configuration DNS Server ConfigurationSpanning Tree Algorithm / Redundancy Multiple AP Repeater Mesh Network 3A1582Rev1.6 Example Extending range using WDS Site B WDS ConfigurationExample Roaming with WDS Access Points Example Adding Redundancy3A1582Rev1.6 Example WDS Routed Network Mouse, to highlight the entire row Routing Rules WDS ConnectionsSTP Wireless Message Filtering Specifies a destination hostInformation at a later time 3A1582Rev1.6 MAC Address Filter Configuration IP Address Filter ConfigurationUtilize the radio link. All other devices are blocked ARP Filter Configuration Serial Port Configuration RS-232 PPP ServerSerial Gateway Server/Client/Multicast Serial Gateway Modbus Modbus RTU to TCPModbus TCP to RTU Gateway Serial MenuMulticast Pipe Manager Multicast Group IP Address Digital Input/OutputPort on the Client, i.e., Scada, DCS, etc To be the same on all communicating Multicast devicesModbus I/O Transfer 3A1582Rev1.6 Modbus TCP Configuration on I/O Transfer Menu Module Information Configuration Modbus TCP Client Mappings on I/O Transfer MenuModule Information Webpage Fields Remote Configuration System ToolsConfiguration Examples Setting a BU-945U-E to Factory Default SettingsExtending a Wired Network Client 1 Configuration Client 2 ConfigurationLAN B Configuration Access Point Configuration Client ConfigurationExtending Range of a Network with a Repeater Hop LED Indicator Condition Meaning Diagnostics ChartBoot Status LED Indication during Start-up RED ContinuouslyConnectivity Parameters Diagnostic Information AvailableConnectivity Site SurveyStatistics Network Traffic AnalysisConnection Information Internal Diagnostic Modbus Registers9999 Both Reset module enter Ffff to reset module 5014 STA OnlyStatistic Registers Testing Radio Paths UtilitiesPing 3A1582Rev1.6 Ipconfig ArpRoute Radio Transceiver Power SupplyGeneral Serial PortsSystem Parameters Input / Output statusWeb-Based Upgrade Appendix a Firmware UpgradesCSMA/CD ACKCSMA/CA DhcpIeee IPX-SPXISN NIC SNRNAT SSLWAN VoIPVPN WEPDBm to mW Conversion Installation MaterialsIperf Applications 3A1582Rev1.6 JPerf Application 3A1582Rev1.6 Preamble Terms and Conditions3A1582Rev1.6 No Warranty 3A1582Rev1.6 Customer Assistance