Xerox 721P manual Clearing Media Jam J-04

Page 46

PROBLEM SOLVING

Clearing Media Jam (J-04)

When a jam J-04 occurs, the media jams while feeding from Roll 4 in the bottom drawer.

Fuser

Handle

Cutter

handle

Inner Transport handle

Down Lock

MF

Exit

 

 

 

 

 

 

 

D1

PF

 

 

 

D2

 

 

 

Copy Density

Menu

Enter

Online

D3

D4

 

 

 

1.Open the bottom drawer.

2.Open the Right Side Door and turn the Inner Transport Assembly handle to release the transport. Lower and lock the transport by engaging the Down Lock.

3.If the media is not cut and the leading edge of the media has reached the Drum or beyond the Drum, rotate the Cutter handle to cut the media. Continue rotating the cutter handle so that the green home position indicator appears in the cut out.

4.If the leading edge of the media has reached the Fuser Unit, open the Exit Cover and remove the jammed media by rotating the Fuser Handle.

Slit

Cutter

5.Release the Down Lock while holding the handle of Inner Transport Assembly and lift it up gently until it stops. Then twist the handle to the left to move the transport to the home position. Finally, turn the handle to the right to lock the transport.

6.Manually rewind the roll until the lead edge of the media is free of the feed rollers.

7.Trim the lead edge of the roll square to remove any torn or wrinkled media by using the “Slit” if necessary.

38

XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL

Image 46
Contents Xerox Wide Format 721P Printer Operator Manual Page Table of contents User Modes Safety Notes Introduction European Union EMC NoticesAustralia/New Zealand CanadaJapan USAIntroduction IntroductionOrganization And Content Of This Manual Terminology Used In This ManualConventions Used In This Manual BoldThis page is intentionally blank Specification Product SpecificationsMedia Specifications Room Space Requirements Room Space RequirementsSerial Number Location Room Air Change Requirements For Ozone DissipationThis page is intentionally blank Printer Overview Printer OrientationMain Components Service use only Pins Not UsedPins Rear Side ViewPrinter Overview Ready Indicator Operator Panel & Status DisplayMedia and Toner Status Panel Use IndicatorsRoll Size Displays Displays the size of the roll media Online/Offline Job Cancel Media Adding Media RollsLoading The Roll Media Roll 1, 2 Roll 3 only Loading The Roll Media Roll Belt Loading The Roll Media When Printing Dehumidifier Using Manual Bypass Feed When The Toner Cartridge Needs Replacement CareReplacing The Toner Cartridge Sealed opening Cleaning The Charge Scorotron Wire Wire-CleanCleaning The LED Print Head Exp-CleanCleaning The Printer Surface Ordering supplies Supply order procedureSupply order list This page is intentionally blank Problem Solving Media JamsClearing Media Jam J-01 & J-02 Problem Solving Clearing Media Jam J-03 Problem Solving Clearing Media Jam J-04 Green Knob Clearing Media Jam J-05 Clearing Media Jam J-11 & J-12 Slit Clearing Media Jam J-13 & J-14 Clearing Media Jam J-22 Printer Errors E-XX Error CodesError Code Cause Treatment Door Open Errors U-XX Thumping Noise in StandbyImage Quality Problem Solving Problem Cause SolutionThis page is intentionally blank User Mode 1 Test Print U1 User ModesUser Modes User Mode 2 Date and Time setting U2 Hour Minute Second User Mode 3 Low Power Saver Mode U3 User Modes User Mode 4 High Power Saver Mode U4 User Modes User Mode 5 Media Cut At Power on U5 User Mode 6 Detack Lamp Control Mode U6 User Mode 7 Attention Beeper Enable Mode U7 User Mode 8 Custom Setting Plain Paper U8 User Mode 9 Custom Setting Vellum/Tracing Paper U9 User Mode a Custom Setting Film UA User Mode b Image Enhancement Ub USA 701P39415 4/2003