Xerox 721P manual Safety Notes

Page 5

TABLE of CONTENTS

Safety Notes

Your Xerox Wide Format 721P Engineering Printer has been designed and tested to meet strict safety requirements. These include safety agency examination and approval and compliance to established environmental standards.

Please read the following instructions carefully before operating the Xerox Wide Format 721P Engineering Printer and refer to them as needed to ensure the continued safe operation of the product.

Follow all warnings and instructions marked on or supplied with the product.

Unplug the printer from the wall outlet before cleaning the exterior. Always use materials specifically designated for the Xerox Wide Format 721P Engineering Printer. Use of other materials may result in poor performance and could create a hazardous situation.

Do not use aerosol cleaners. Follow the instructions in this operator manual for the proper cleaning methods.

Never use supplies or cleaning materials for purposes other than what they were intended. Keep all supplies and materials out of the reach of children.

Do not use this product near water, wet locations, or outdoors.

This product is equipped with a three-wire, grounding-type plug (i.e., a plug having a grounding pin). This plug will only fit into a grounding-type power outlet. This is a safety feature. To avoid the risk of electric shock, contact your electrician to replace the receptacle if you are unable to insert the plug into the outlet.

Never use a ground adapter plug to connect the printer to a power source that lacks a ground connection terminal.

This product should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your local power company.

The power supply cord is the disconnect device for this equipment. Make sure that the installation is near the socket outlet and is easily accessible.

Do not allow anything to rest on the power cord. Do not locate the printer where someone will step on the cord.

Slots and openings in the cabinet and in the back and bottom of the printer are provided for ventilation. To ensure reliable operation of the printer and to protect it from overheating, these openings should never be placed near a radiator or heat register. The printer should not be placed in a built-in installation unless proper ventilation is provided.

Never push objects of any kind into the slots of the printer as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock.

Never spill liquid of any kind on the printer.

XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL

v

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Xerox Wide Format 721P Printer Operator Manual Page Table of contents User Modes Safety Notes Introduction Australia/New Zealand EMC NoticesEuropean Union CanadaUSA JapanIntroduction IntroductionTerminology Used In This Manual Organization And Content Of This ManualBold Conventions Used In This ManualThis page is intentionally blank Product Specifications SpecificationMedia Specifications Serial Number Location Room Space RequirementsRoom Space Requirements Room Air Change Requirements For Ozone DissipationThis page is intentionally blank Printer Orientation Printer OverviewMain Components Pins Pins Not UsedService use only Rear Side ViewPrinter Overview Operator Panel & Status Display Ready IndicatorRoll Size Displays Displays the size of the roll media Use IndicatorsMedia and Toner Status Panel Online/Offline Job Cancel Adding Media Rolls MediaLoading The Roll Media Roll 1, 2 Roll 3 only Loading The Roll Media Roll Belt Loading The Roll Media When Printing Dehumidifier Using Manual Bypass Feed Care When The Toner Cartridge Needs ReplacementReplacing The Toner Cartridge Sealed opening Wire-Clean Cleaning The Charge Scorotron WireExp-Clean Cleaning The LED Print HeadCleaning The Printer Surface Supply order list Supply order procedureOrdering supplies This page is intentionally blank Media Jams Problem SolvingClearing Media Jam J-01 & J-02 Problem Solving Clearing Media Jam J-03 Problem Solving Clearing Media Jam J-04 Green Knob Clearing Media Jam J-05 Clearing Media Jam J-11 & J-12 Slit Clearing Media Jam J-13 & J-14 Clearing Media Jam J-22 Error Code Cause Treatment Error CodesPrinter Errors E-XX Thumping Noise in Standby Door Open Errors U-XXProblem Cause Solution Image Quality Problem SolvingThis page is intentionally blank User Modes User Mode 1 Test Print U1User Modes User Mode 2 Date and Time setting U2 Hour Minute Second User Mode 3 Low Power Saver Mode U3 User Modes User Mode 4 High Power Saver Mode U4 User Modes User Mode 5 Media Cut At Power on U5 User Mode 6 Detack Lamp Control Mode U6 User Mode 7 Attention Beeper Enable Mode U7 User Mode 8 Custom Setting Plain Paper U8 User Mode 9 Custom Setting Vellum/Tracing Paper U9 User Mode a Custom Setting Film UA User Mode b Image Enhancement Ub 701P39415 4/2003 USA
Top Page Image Contents