Xerox 721P manual User Mode 3 Low Power Saver Mode U3

Page 61

USER MODES

User Mode 3 (Low Power Saver Mode) “U3”

Menu

Enter

Online

Press [Menu] 3 times

Menu

Enter

Online

Menu

Enter

Online

If the Low Power Saver Mode is enabled, the printer reduces

power to the Printer Fuser Assembly from 178C to 100C after a predetermined period of inactivity. If the printer does not receive a print job or copy job for the time selected in this mode the printer will enter the Low Power Saver Mode to save power consumption.

If a print or copy job is detected by the printer, the printer will then enter the Warm up Mode prior to the start of the job to heat the Fuser Assembly to 178C.

The green LED Light inside of the Menu Button flashes when the printer is in a power saver mode.

1. To enter User Mode 3:

Press the [Menu] Key 3 times when the printer is in the Standby (idle) Mode.

The [Menu] Key lights green and the Status Display indicates “U3" flashing on the left side of the display. The right side of the display shows the current setting (in minutes).

2. Press [Enter]

The status (on or off) is displayed. If the status is off, Low Power Saver is disabled.

To change the status, press [Enter] and then the [ --> ] Key or the [ <-- ] Key.

3.Press [Enter] again for access to the time interval. The current setting (in minutes) is displayed.

The selectable ranges are 10, 15, 20, 30, 40, 50, 60, 90, 120, 180 and 240 minutes. (Factory default is On and set to 15 minutes)

To change the time, press the [ --> ] Key to increase) and the [ <-- ] Key to decrease, then press [Enter] to save the data.

XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL

53

Image 61

Contents Xerox Wide Format 721P Printer Operator Manual Page Table of contents User Modes Safety Notes Introduction Australia/New Zealand EMC NoticesEuropean Union CanadaUSA JapanIntroduction IntroductionTerminology Used In This Manual Organization And Content Of This ManualBold Conventions Used In This ManualThis page is intentionally blank Product Specifications SpecificationMedia Specifications Serial Number Location Room Space RequirementsRoom Space Requirements Room Air Change Requirements For Ozone DissipationThis page is intentionally blank Printer Orientation Printer OverviewMain Components Pins Pins Not UsedService use only Rear Side ViewPrinter Overview Operator Panel & Status Display Ready IndicatorMedia and Toner Status Panel Use IndicatorsRoll Size Displays Displays the size of the roll media Online/Offline Job Cancel Adding Media Rolls MediaLoading The Roll Media Roll 1, 2 Roll 3 only Loading The Roll Media Roll Belt Loading The Roll Media When Printing Dehumidifier Using Manual Bypass Feed Care When The Toner Cartridge Needs ReplacementReplacing The Toner Cartridge Sealed opening Wire-Clean Cleaning The Charge Scorotron WireExp-Clean Cleaning The LED Print HeadCleaning The Printer Surface Ordering supplies Supply order procedureSupply order list This page is intentionally blank Media Jams Problem SolvingClearing Media Jam J-01 & J-02 Problem Solving Clearing Media Jam J-03 Problem Solving Clearing Media Jam J-04 Green Knob Clearing Media Jam J-05 Clearing Media Jam J-11 & J-12 Slit Clearing Media Jam J-13 & J-14 Clearing Media Jam J-22 Printer Errors E-XX Error CodesError Code Cause Treatment Thumping Noise in Standby Door Open Errors U-XXProblem Cause Solution Image Quality Problem SolvingThis page is intentionally blank User Modes User Mode 1 Test Print U1User Modes User Mode 2 Date and Time setting U2 Hour Minute Second User Mode 3 Low Power Saver Mode U3 User Modes User Mode 4 High Power Saver Mode U4 User Modes User Mode 5 Media Cut At Power on U5 User Mode 6 Detack Lamp Control Mode U6 User Mode 7 Attention Beeper Enable Mode U7 User Mode 8 Custom Setting Plain Paper U8 User Mode 9 Custom Setting Vellum/Tracing Paper U9 User Mode a Custom Setting Film UA User Mode b Image Enhancement Ub 701P39415 4/2003 USA