Xerox 721P manual User Mode 4 High Power Saver Mode U4

Page 63

USER MODES

User Mode 4 (High Power Saver Mode) “U4”

Menu

Enter

Online

Press [Menu] 4 times

Menu

Enter

Online

Menu

Enter

Online

When the High Power Saver Mode is enabled, the printer switches off power to the Printer Fuser Assembly after a predetermined time of inactivity. If the printer does not receive a print job or a copy job for the time selected in this mode, the printer will enter the High Power Saver Mode to save power consumption.

The High Power Saver Mode saves more power than the Low Power Saver Mode and the recovery time is longer.

If a print or copy job is detected by the printer, the printer will then enter the Warm up Mode prior to the start of the job to heat the Fuser Assembly to 178C.

The green LED Light inside of the Menu Button flashes when the printer is in a power saver mode.

1. To enter User Mode 4:

Press the [Menu] Key 4 times when the printer is in the Standby (idle) Mode.

The [Menu] Key lights green and the Status Display indicates “U4.” Flashing on the left side of the display. The time interval is shown on the right side of the display.

NOTE: Factory default is On and set to 90 minutes.

2. Press [Enter]

The status (on or off) is displayed. If the status is off, High Power Saver is disabled.

To change the status, press [Enter] and then the [ --> ] Key or the [ <-- ] Key.

Press [Enter] again to gain access to the time interval.

To change the time, press [ --> ] Key to increase) and [ <-- ] Key to decrease, then press [Enter] to save the data.

The display value is “minute”, and the selectable ranges are 10, 15, 20, 30, 40, 50, 60, 90, 120, 180 and 240.

XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL

55

Image 63

Contents Xerox Wide Format 721P Printer Operator Manual Page Table of contents User Modes Safety Notes Introduction Canada EMC NoticesAustralia/New Zealand European UnionUSA JapanIntroduction IntroductionTerminology Used In This Manual Organization And Content Of This ManualBold Conventions Used In This ManualThis page is intentionally blank Product Specifications SpecificationMedia Specifications Room Air Change Requirements For Ozone Dissipation Room Space RequirementsSerial Number Location Room Space RequirementsThis page is intentionally blank Printer Orientation Printer OverviewMain Components Rear Side View Pins Not UsedPins Service use onlyPrinter Overview Operator Panel & Status Display Ready IndicatorUse Indicators Media and Toner Status PanelRoll Size Displays Displays the size of the roll media Online/Offline Job Cancel Adding Media Rolls MediaLoading The Roll Media Roll 1, 2 Roll 3 only Loading The Roll Media Roll Belt Loading The Roll Media When Printing Dehumidifier Using Manual Bypass Feed Care When The Toner Cartridge Needs ReplacementReplacing The Toner Cartridge Sealed opening Wire-Clean Cleaning The Charge Scorotron WireExp-Clean Cleaning The LED Print HeadCleaning The Printer Surface Supply order procedure Ordering suppliesSupply order list This page is intentionally blank Media Jams Problem SolvingClearing Media Jam J-01 & J-02 Problem Solving Clearing Media Jam J-03 Problem Solving Clearing Media Jam J-04 Green Knob Clearing Media Jam J-05 Clearing Media Jam J-11 & J-12 Slit Clearing Media Jam J-13 & J-14 Clearing Media Jam J-22 Error Codes Printer Errors E-XXError Code Cause Treatment Thumping Noise in Standby Door Open Errors U-XXProblem Cause Solution Image Quality Problem SolvingThis page is intentionally blank User Modes User Mode 1 Test Print U1User Modes User Mode 2 Date and Time setting U2 Hour Minute Second User Mode 3 Low Power Saver Mode U3 User Modes User Mode 4 High Power Saver Mode U4 User Modes User Mode 5 Media Cut At Power on U5 User Mode 6 Detack Lamp Control Mode U6 User Mode 7 Attention Beeper Enable Mode U7 User Mode 8 Custom Setting Plain Paper U8 User Mode 9 Custom Setting Vellum/Tracing Paper U9 User Mode a Custom Setting Film UA User Mode b Image Enhancement Ub 701P39415 4/2003 USA