Xerox 721P manual User Mode 2 Date and Time setting U2

Page 59

USER MODES

User Mode 2 (Date and Time setting) “U2”

Menu

Enter

Online

Press [Menu] twice

Menu

Enter

Online

Enter User Mode 2 to set the correct date and time.

Note: Although there will be no performance problems if the date and time are incorrect, the printer automatically records the date and time errors occur. This information can be critical for service problem solving. It is recommended the date and time be set correctly.

1. To enter User Mode 2:

Press the [Menu] Key twice when the printer is in the Standby (idle) Mode.

The [Menu] Key lights green and the Status Display indicates “U2.” flashing on the left side of the display.

2. Press the [ <-- ] Key.

C6 appears in the left side of the display and the scrolling seconds time is displayed in the right side of the display. The seconds can now be changed.

3. To change the seconds, press [Enter]. The seconds stop scrolling and begin to flash.

4.To change the value, press the [ --> ] Key to increase the value and [ <-- ] Key to decrease the value.

5.Press [Enter] to store the value.

There are 6 setting locations: C6 - seconds, C5 - minutes, C4 - hour, C3 - day, C2 - month, C1 - year, in sequence with each press of the [ <-- ] Key.

XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL

51

Image 59

Contents Xerox Wide Format 721P Printer Operator Manual Page Table of contents User Modes Safety Notes Introduction Canada EMC NoticesAustralia/New Zealand European UnionUSA JapanIntroduction IntroductionTerminology Used In This Manual Organization And Content Of This ManualBold Conventions Used In This ManualThis page is intentionally blank Product Specifications SpecificationMedia Specifications Room Air Change Requirements For Ozone Dissipation Room Space RequirementsSerial Number Location Room Space RequirementsThis page is intentionally blank Printer Orientation Printer OverviewMain Components Rear Side View Pins Not UsedPins Service use onlyPrinter Overview Operator Panel & Status Display Ready IndicatorRoll Size Displays Displays the size of the roll media Use IndicatorsMedia and Toner Status Panel Online/Offline Job Cancel Adding Media Rolls MediaLoading The Roll Media Roll 1, 2 Roll 3 only Loading The Roll Media Roll Belt Loading The Roll Media When Printing Dehumidifier Using Manual Bypass Feed Care When The Toner Cartridge Needs ReplacementReplacing The Toner Cartridge Sealed opening Wire-Clean Cleaning The Charge Scorotron WireExp-Clean Cleaning The LED Print HeadCleaning The Printer Surface Supply order list Supply order procedureOrdering supplies This page is intentionally blank Media Jams Problem SolvingClearing Media Jam J-01 & J-02 Problem Solving Clearing Media Jam J-03 Problem Solving Clearing Media Jam J-04 Green Knob Clearing Media Jam J-05 Clearing Media Jam J-11 & J-12 Slit Clearing Media Jam J-13 & J-14 Clearing Media Jam J-22 Error Code Cause Treatment Error CodesPrinter Errors E-XX Thumping Noise in Standby Door Open Errors U-XXProblem Cause Solution Image Quality Problem SolvingThis page is intentionally blank User Modes User Mode 1 Test Print U1User Modes User Mode 2 Date and Time setting U2 Hour Minute Second User Mode 3 Low Power Saver Mode U3 User Modes User Mode 4 High Power Saver Mode U4 User Modes User Mode 5 Media Cut At Power on U5 User Mode 6 Detack Lamp Control Mode U6 User Mode 7 Attention Beeper Enable Mode U7 User Mode 8 Custom Setting Plain Paper U8 User Mode 9 Custom Setting Vellum/Tracing Paper U9 User Mode a Custom Setting Film UA User Mode b Image Enhancement Ub 701P39415 4/2003 USA