Extron electronic 1616 HV, HVA manual Video input and output connections

Page 15

Video input and output connections

2

3

All video input and output connections to the CrossPoint Plus switchers are made with female BNC connectors. Some types of video output devices do not have BNC video output connectors. For these cases, a suitable cable or connector adapter is necessary between the device output connector and the BNC input connector of the CrossPoint Plus.

RGBHV video inputs — Connect RGBHV video inputs to these BNC connectors for each input.

RGBHV video outputs — Connect RGBHV video outputs to these BNC connectors for each output.

The CrossPoint Plus Series switchers can also switch RGBS, RGsB, RsGsBs, component video, S-video, or composite video by using four, three, two, or one BNC. If switching a video format other than RGBHV, ensure that the same video planes (R, G, B, H/HV, and/or V) are used on the switcher output as on the input.

The CrossPoint Plus Series Matrix Switchers do not alter the video signal in any way. The signal output by the switcher is in the same format as the input.

Audio input and output connections (HVA models only)

CAUTION

The captive screw connector can easily be inadvertently plugged partially into one receptacle and partially into an adjacent receptacle. This misconnection could damage the audio output circuits. Exercise care to ensure the captive screw connector is plugged into the desired input or output.

4Connections for balanced and unbalanced audio inputs — Each input has a

3.5mm, 5-pole captive screw connector for balanced or unbalanced stereo audio input. Connectors are included

with each CrossPoint Plus switcher, but you must supply the audio cable. See figure 2-3 to wire a connector for the appropriate input type and impedance level. High impedance is generally over 800 ohms.

Tip Sleeve

Tip Sleeve

Tip

Ring

Sleeve (s)

Tip

Ring

600 ohms

Tip

Ring

Sleeve (s)

Tip

Ring

 

 

600 ohms

Unbalanced Input

Balanced Input

Balanced Input

(high impedance)

(high impedance)

(600 ohms)

Figure 2-3 — Captive screw connector wiring for inputs

When making connections for the CrossPoint Plus Series Switcher from existing audio cables, see figure 2-4. A mono audio connector consists of the tip and sleeve. A stereo audio connector consists of the tip, ring and sleeve. The ring, tip, and sleeve wires are also shown on the captive screw audio connector diagrams, figure 2-3 and figure 2-5.

The audio level for each input can be individually set, via the front panel or RS-232/422, to ensure that the level on the output does not vary from input to input. See chapter 3, Operation, chapter 4, Programmer’s Guide, and chapter 5, Matrix Software, for details.

CrossPoint Plus Matrix Switchers • Installation

2-3

Page 14 Page 16
Image 15
Page 14 Page 16
Contents CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQuick Start CrossPoint Plus Matrix Switchers Create a tie Quick Start CrossPoint Plus Matrix Switchers, cont’dSave or recall a preset View and adjust audio levelTable of Contents Table of Contents, cont’d One About the CrossPoint Plus Series Matrix Switchers CrossPoint Plus Matrix Switchers IntroductionIntroductiontroduction, cont’d CrossPoint Plus 128HVA FeaturesMatrix Input Status Introduction, cont’dAudio gain and attenuation Any input to any or all outputs Two CrossPoint Plus Matrix Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Power connectionAudio input and output connections HVA models only Video input and output connectionsRS-232/422 connection Installation, cont’dRear panel view, CrossPoint Plus 84HV Additional rear panel views11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Definitions Front Panel Controls and IndicatorsCrossPoint Plus Matrix Switchers Operation Operationeration, cont’dControl buttons and LEDs Input buttons, output buttons, and LEDsOperation, cont’d ControlsFront panel I/O label windows Power Front Panel OperationsGrouping Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step d Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presetsExample 7 Recall a preset Example 6 Save a presetExample 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockoutGeneral checks TroubleshootingSystem reset to factory defaults Rear Panel ControlsPlasma display S-video problem WorksheetsWorksheet example 1 Entering system equipment Worksheet example 2 Drawing ties Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetOperation, cont’d Four Programmer’ser’sGuide,Guidecont’d Host-to-Switcher InstructionsSwitcher-Initiated Messages CrossPoint Plus Matrix Switchers Programmer’s GuideUsing the Command/Response Table Switcher Error ResponsesCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five MatrixSoftware,cont’d Matrix Switchers Control ProgramInstalling the software Using the softwareWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’dAudio audio models only Audio input audio models onlyAudio output audio models only Extron Part Specifications, cont’dPart Numbers CrossPoint Plus part numbersCables Optional accessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesAppendixBB ReferenceInformation,co t’d Hardware UpgradesOpening the switcher CrossPoint Plus Matrix Switchers Reference InformationFigure B-2 Removing the front cover Closing the switcher Reference Information, cont’dSwapping the serial ports Figure B-4 Key and pin 1 mark Installing a firmware updateButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents