Extron electronic HVA, 1616 HV manual Creating a configuration

Page 26

Operation, cont’d

The I/O groups can be set up only by using the RS-232/422 port and either the SIS or the Windows control program. Ties between groups (an input in group 1 tied to an output in group 2) can be created under RS-232/422 control. Presets can also be created under RS-232/422 control that tie inputs and outputs across group boundaries. These presets are selectable from the front panel.

Suggested applications for the I/O grouping feature include:

•Segregating specific video formats to prevent an input in one video format from being inadvertently applied to an output device that supports another video format.

•Segregating input and output devices that are in separate rooms.

•Isolating video from being displayed on specific output devices for operational security reasons.

The I/O groups created under RS-232/422 control can result in front panel indications that are different from indications when grouping is not used. In the following paragraphs, the effects of I/O grouping on the front panel indications are included.

Creating a configuration

The current configuration can be changed using the front panel buttons. To change the current configuration, do the following:

1.

Press the Esc button to clear any input LEDs, output LEDs, or control LEDs

 

that may be on.

2.Select to configure video, audio, or both by pressing the RGBHV and/or Audio buttons.

3.Select the desired input and output(s) by pressing the input and output buttons.

4.

Press and release the Enter button.

5.

Repeat steps 1 through 4 to create additional ties until the desired

 

configuration is complete.

1. Only one video input and one audio input can be tied to an output.

2.If a tie is made between an input and an output, and the selected output was previously tied to another input, the older tie is broken in favor of the newer tie.

3.To indicate current ties, output LEDs light when an input is selected. To clear unwanted outputs press and release the associated output buttons.

4.If, when configuring video and audio ties, the Audio LED blinks and the RGBHV LED is on after selecting an input or output, the LEDs indicate audio breakaway, meaning that the audio ties are not the same as the video ties for that input.

5.If an input with no tie is selected, only that input’s LED lights.

6.When the RGBHV and Audio LEDs are on, if an input with an audio tie but no video tie is selected, the input’s LED lights and the Audio LED blinks.

7.As each output is selected, the associated output LED blinks to indicate a tentative tie. LEDs for output(s) that were already tied to the input light steadily. Outputs that are already tied can be left on, along with new blinking selections, or toggled off by pressing the associated output button.

3-6 CrossPoint Plus Matrix Switchers • Operation

Page 25 Page 27
Image 26
Page 25 Page 27
Contents CrossPoint Plus Matrix Switchers CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVASicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers View and adjust audio level Quick Start CrossPoint Plus Matrix Switchers, cont’dSave or recall a preset Create a tieTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Plus Series Matrix SwitchersCrossPoint Plus Matrix Switchers Introduction Features CrossPoint Plus 128HVAIntroduction, cont’d Matrix Input StatusAudio gain and attenuation Any input to any or all outputs Two Power connection Installationstallation, cont’dRack Mounting the Switcher CrossPoint Plus Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint Plus 84HV11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint Plus Matrix Switchers Operation DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsFront panel I/O label windows Operation, cont’dControls Grouping PowerFront Panel Operations Creating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step d Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets 13 Example 5, step d Muting and unmuting outputsExample 6 Save a preset Example 7 Recall a presetViewing and adjusting the input audio level HVA models only Example 8 View and adjust an audio level17 +8dB displayed, CrossPoint Plus 168 Executive mode front panel security lockout 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint PlusRear Panel Controls TroubleshootingSystem reset to factory defaults General checksWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets Worksheet example 3 Test configuration Worksheet example 2 Drawing tiesMatrix Switchers Configuration Worksheet Preset #Operation, cont’d Four CrossPoint Plus Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Using the software Matrix Switchers Control ProgramInstalling the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Plus Matrix Switchers SpecificationsAudio output audio models only Audio audio models onlyAudio input audio models only CrossPoint Plus part numbers Specifications, cont’dPart Numbers Extron PartOptional accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableAppendixBB CrossPoint Plus Matrix Switchers Reference Information Hardware UpgradesOpening the switcher ReferenceInformation,co t’dFigure B-2 Removing the front cover Swapping the serial ports Closing the switcherReference Information, cont’d Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents