Extron electronic HVA, 1616 HV manual Example 5 Muting and unmuting an output

Page 32

Operation, cont’d

4.

One at a time, press and hold the output button(s) for the desired output(s)

 

for approximately 2 seconds. The output LED(s) for the selected output(s)

 

blink to indicate the mute or return to their previous state to indicate the

 

unmute.

5.

Press and release the View button to return to normal switcher operation.

1. You can mute video and audio, video-only, or audio-only outputs. Pressing and releasing the RGBHV and Audio buttons toggles each selection on and off.

2.When you enter view-only mode, the output LEDs turn on for all outputs without ties.

3.The video mute function mutes the R, G, and B planes only; the H and V planes are still active.

4.Mutes are not saved to non-volatile memory. When power is removed and restored, the mute settings are lost.

Example 5: Muting and unmuting an output

See figure 3-9, on page 3-10, and figure 3-13 and the following steps for an example of muting and unmuting several CrossPoint Plus switcher outputs.

Figure 3-9 shows the process of viewing the current configuration after the steps in Examples 1, 2, and 3 have been completed.

APress and release the Esc button. The Esc LED flashes once.

BPress and release the View button to enter view-only mode. The View LED lights.

CTo select both video and audio for viewing, if necessary, press and release the RGBHV and Audio buttons until the RGBHV LED and Audio LED light. With no input LED selected, all output LEDs that have no established ties light.

DOne at a time, press an hold the Output 3 and Output 4 buttons (figure 3-13) for approximately 2 seconds until the associated output LED begins to blink. The output 3 and output 4 video and audio signals are muted.

Figure 3-13 shows only the indications directly related to the mute operation. Indications from existing ties are not shown to avoid confusion.

EOne at a time, press and hold the Output 3 and Output 4 LEDs for approximately 2 seconds until the associated output LED lights steadily. The output 3 and output 4 video and audio signals are unmuted.

FPress and release the View button to exit view-only mode. The View LED and all input and output LEDs go out.

3-12 CrossPoint Plus Matrix Switchers • Operation

Page 31 Page 33
Image 32
Page 31 Page 33
Contents CrossPoint Plus Matrix Switchers CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVASafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers Quick Start CrossPoint Plus Matrix Switchers, cont’d Save or recall a presetView and adjust audio level Create a tieTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Plus Series Matrix SwitchersCrossPoint Plus Matrix Switchers Introduction Features CrossPoint Plus 128HVAIntroduction, cont’d Matrix Input StatusAudio gain and attenuation Any input to any or all outputs Two Installationstallation, cont’d Rack Mounting the SwitcherPower connection CrossPoint Plus Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint Plus 84HV11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Front Panel Controls and Indicators CrossPoint Plus Matrix Switchers OperationOperationeration, cont’d DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsFront panel I/O label windows Operation, cont’dControls Grouping PowerFront Panel Operations Creating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step d Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets 13 Example 5, step d Muting and unmuting outputsExample 6 Save a preset Example 7 Recall a presetViewing and adjusting the input audio level HVA models only Example 8 View and adjust an audio level17 +8dB displayed, CrossPoint Plus 168 Executive mode front panel security lockout 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint PlusTroubleshooting System reset to factory defaultsRear Panel Controls General checksWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets Worksheet example 3 Test configuration Worksheet example 2 Drawing tiesMatrix Switchers Configuration Worksheet Preset #Operation, cont’d Four Host-to-Switcher Instructions Switcher-Initiated MessagesCrossPoint Plus Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Matrix Switchers Control Program Installing the softwareUsing the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Plus Matrix Switchers SpecificationsAudio output audio models only Audio audio models onlyAudio input audio models only Specifications, cont’d Part NumbersCrossPoint Plus part numbers Extron PartOptional accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableAppendixBB Hardware Upgrades Opening the switcherCrossPoint Plus Matrix Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Removing the front cover Swapping the serial ports Closing the switcherReference Information, cont’d Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents