Extron electronic 1616 HV, HVA manual Example 1 Create a set of video and audio ties

Page 27

8.If the input button for a grouped input is pressed, and then the output button for an output in a different group is pressed, the associated output LED blinks twice and goes out to indicate that output cannot be tied to the input. The associated input LED remains lit.

Example 1: Create a set of video and audio ties

See Figure 3-5 and the following steps for an example in which input 5 is tied to outputs 3, 4, and 8.

This example assumes that there are no ties in the current configuration.

5

LED key:

= off,

= on, B = blinking,

Press

Press

Press

F

= flash once

B

C

RGBHV AUDIO

INPUTS

1

2

3

4

5

6

7

8

9

10

11

12

CONTROL

I/O

1

2

3

4

5

6

7

8

ENTER PRESET VIEW

ESC

RGBHV AUDIO

OUTPUTS

Press

B

Press

B

B

Press

F

		D	E
3	4	8	ENTER

A

ESC

Figure 3-5 — Example 1: Creating a tie

APress and release the Esc button. The Esc LED flashes once.

BIf necessary to select video and audio for the tie, press and release the RGBHV and Audio buttons until the RGBHV and Audio LEDs light.

CPress and release the input 5 button. The input 5 LED lights.

DPress and release the output 3, output 4, and output 8 buttons. The output 3, output 4, and output 8 LEDs blink to indicate a tentative tie.

The entire set of ties can be aborted at this point by pressing and releasing the Esc button. The Esc LED flashes once.

EPress and release the Enter button. The input and output LEDs turn off. The current configuration is now defined as video and audio input 5 tied to video and audio output 3, output 4, and output 8.

Example 2: Add a tie to a set of video and audio ties

See figure 3-6 and the following steps for an example in which a new video tie is added to the current configuration.

APress and release the Esc button. The Esc LED flashes once.

BIf it is necessary to select video-only for the tie, press and release the RGBHV and Audio buttons until the RGBHV LED lights and the Audio LED is off.

CPress and release the input 5 button. The input 5 LED lights. If the steps in Example 1 have been completed, the output 3, output 4, and output 8 LEDs light to indicate ties created in Example 1.

DPress and release the output 1 button. The output 1 LED blinks to indicate a tentative tie.

CrossPoint Plus Matrix Switchers • Operation

3-7

Image 27

Contents CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQuick Start CrossPoint Plus Matrix Switchers Create a tie Quick Start CrossPoint Plus Matrix Switchers, cont’dSave or recall a preset View and adjust audio levelTable of Contents Table of Contents, cont’d One About the CrossPoint Plus Series Matrix Switchers CrossPoint Plus Matrix Switchers IntroductionIntroductiontroduction, cont’d CrossPoint Plus 128HVA FeaturesMatrix Input Status Introduction, cont’dAudio gain and attenuation Any input to any or all outputs Two CrossPoint Plus Matrix Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Power connectionAudio input and output connections HVA models only Video input and output connectionsRS-232/422 connection Installation, cont’dRear panel view, CrossPoint Plus 84HV Additional rear panel views11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Definitions Front Panel Controls and IndicatorsCrossPoint Plus Matrix Switchers Operation Operationeration, cont’dControl buttons and LEDs Input buttons, output buttons, and LEDsOperation, cont’d ControlsFront panel I/O label windows Power Front Panel OperationsGrouping Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step d Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presetsExample 7 Recall a preset Example 6 Save a presetExample 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockoutGeneral checks TroubleshootingSystem reset to factory defaults Rear Panel ControlsPlasma display S-video problem WorksheetsWorksheet example 1 Entering system equipment Worksheet example 2 Drawing ties Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetOperation, cont’d Four Programmer’ser’sGuide,Guidecont’d Host-to-Switcher InstructionsSwitcher-Initiated Messages CrossPoint Plus Matrix Switchers Programmer’s GuideUsing the Command/Response Table Switcher Error ResponsesCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five MatrixSoftware,cont’d Matrix Switchers Control ProgramInstalling the software Using the softwareWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’dAudio audio models only Audio input audio models onlyAudio output audio models only Extron Part Specifications, cont’dPart Numbers CrossPoint Plus part numbersCables Optional accessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesAppendixBB ReferenceInformation,co t’d Hardware UpgradesOpening the switcher CrossPoint Plus Matrix Switchers Reference InformationFigure B-2 Removing the front cover Closing the switcher Reference Information, cont’dSwapping the serial ports Figure B-4 Key and pin 1 mark Installing a firmware updateButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA