Extron electronic HVA, 1616 HV manual Example 2 Adding a video tie

Page 28

Operation, cont’d

5

LED key:

= off,

= on, B = blinking,

Press

Press

F

= flash once

B

C

RGBHV

INPUTS

1

2

3

4

5

6

7

8

9

10

11

12

CONTROL

I/O

1

2

3

4

5

6

7

8

ENTER PRESET VIEW

ESC RGBHV AUDIO

OUTPUTS

C

C

Press

Press F

B

3

4

8

Press

E

A

D

ENTER

ESC

1

Figure 3-6 — Example 2: Adding a video tie

EPress and release the Enter button. The input and output LEDs turn off. The current configuration is now defined as video input 5 tied to video output 1, output 3, output 4, and output 8; and audio input 5 tied to audio output 3, output 4, and output 8.

Example 3: Remove a tie from a set of video and audio ties

See figure 3-7 and the following steps for an example in which an existing audio tie is removed from the current configuration.

				5					LED key:		= off,	= on,
									LED key:		= off,	= on,
			Press								F = flash once
						C
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12

Press

B

AUDIO

CONTROL I/O

1 2

3

4

5

6

7

8

OUTPUTS

ENTER PRESET VIEW ESC

RGBHV AUDIO

	C	C	Press	F
3	4	8

ESC

A

Figure 3-7 — Example 3: Selecting audio, selecting input 5

APress and release the Esc button. The Esc LED flashes once.

BIf necessary to select audio-only for the tie, press and release the RGBHV and Audio buttons until the RGBHV LED is off and the Audio LED lights.

CPress and release the input 5 button. The input 5 LED lights. If the steps in Example 1 have been completed, the output 3, output 4, and output 8 LEDs light to indicate ties created in Example 1.

The output 1 LED does not light even if the steps in Example 2 were completed because Example 2 added a video tie only.

DPress and release the output 4 button (figure 3-8). The output 4 LED turns off, while the output 3 and output 8 LEDs remain lit.

3-8 CrossPoint Plus Matrix Switchers • Operation

Image 28

Contents CrossPoint Plus Matrix Switchers CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVASafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers Quick Start CrossPoint Plus Matrix Switchers, cont’d Save or recall a presetView and adjust audio level Create a tieTable of Contents Table of Contents, cont’d One CrossPoint Plus Matrix Switchers Introduction About the CrossPoint Plus Series Matrix SwitchersIntroductiontroduction, cont’d Features CrossPoint Plus 128HVAIntroduction, cont’d Matrix Input StatusAudio gain and attenuation Any input to any or all outputs Two Installationstallation, cont’d Rack Mounting the SwitcherPower connection CrossPoint Plus Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint Plus 84HV11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Front Panel Controls and Indicators CrossPoint Plus Matrix Switchers OperationOperationeration, cont’d DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsControls Operation, cont’dFront panel I/O label windows Front Panel Operations PowerGrouping Creating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step d Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets 13 Example 5, step d Muting and unmuting outputsExample 6 Save a preset Example 7 Recall a presetViewing and adjusting the input audio level HVA models only Example 8 View and adjust an audio level17 +8dB displayed, CrossPoint Plus 168 Executive mode front panel security lockout 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint PlusTroubleshooting System reset to factory defaultsRear Panel Controls General checksWorksheets Plasma display S-video problemWorksheet example 1 Entering system equipment Worksheet example 3 Test configuration Worksheet example 2 Drawing tiesMatrix Switchers Configuration Worksheet Preset #Operation, cont’d Four Host-to-Switcher Instructions Switcher-Initiated MessagesCrossPoint Plus Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand Ascii Command Response Additional description Command/Response TableProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Matrix Switchers Control Program Installing the softwareUsing the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing the help system Using emulation modeButton-Label Generator Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Plus Matrix Switchers SpecificationsAudio input audio models only Audio audio models onlyAudio output audio models only Specifications, cont’d Part NumbersCrossPoint Plus part numbers Extron PartOptional accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableAppendixBB Hardware Upgrades Opening the switcherCrossPoint Plus Matrix Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Removing the front cover Reference Information, cont’d Closing the switcherSwapping the serial ports Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA