Extron electronic 1616 HV, HVA manual Audio audio models only, Audio input audio models only

Page 59

Output impedance	75 ohms
Polarity	Positive or negative (follows input)

Audio — audio models only

Routing	84 Series	8 x 4 stereo matrix
	88 Series	8 x 8 stereo matrix
	124 Series	12 x 4 stereo matrix
	128 Series	12 x 8 stereo matrix
	168 Series	16 x 8 stereo matrix
	1616 Series	16 x 16 stereo matrix
Gain	Unbalanced output: 0dB, balanced output: +6dB
Frequency response	20 Hz to 20 kHz, ±0.05dB
THD + Noise	0.03% @ 1 kHz at rated nominal level
S/N	>90dB, balanced, at rated maximum output (21dBu)
Crosstalk	<-80dB @ 1 kHz, fully loaded
Stereo channel separation	>80dB @ 1 kHz
CMRR	>75dB @ 20 Hz to 20 kHz

Audio input — audio models only

Number/signal type	8, 12, or 16 stereo, balanced/unbalanced
Connectors	84/88 Series	(8) 3.5 mm captive screw connectors, 5 pole
	124/128 Series	(12) 3.5 mm captive screw connectors, 5 pole
	168/1616 Series	(16) 3.5 mm captive screw connectors, 5 pole
Impedance	>10 kohm, balanced/unbalanced, DC coupled
Nominal level	-10dBV (316mV)
Maximum level	+19.5dBu, (balanced or unbalanced) at stated %THD+N
Input gain adjustment

84/88/124/128/168/1616 Series

-15dB to +9dB, adjustable per input by RS-232/422 or front panel

Audio output — audio models only

Number/signal type	4, 8, or 16 stereo, balanced/unbalanced
Connectors	84/124 Series	4	3.5 mm captive screw connectors, 5 pole
	88/128/168 Series ....	8	3.5 mm captive screw connectors, 5 pole
	1616 Series	16 3.5 mm captive screw connectors, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±0.1dB channel to channel
Maximum level (Hi-Z)	>+21dBu, balanced or unbalanced at stated %THD+N
Maximum level (600 ohm)	>+15dBm, balanced or unbalanced at stated %THD+N

0dBu = 0.775 volts (RMS).

Control/remote — switcher

Serial control port	1 RS-232 or RS-422, 9-pin female D connector
Baud rate and protocol	9600, 8-bit, 1 stop bit, no parity
Serial control pin configurations ....	2 = TX, 3 = RX, 5 = GND
Program control	Extron’s control program for Windows
	Extron’s Simple Instruction Set™ – SIS™

CrossPoint Plus Matrix Switchers • Specifications

A-3

Image 59

Contents CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQuick Start CrossPoint Plus Matrix Switchers Create a tie Quick Start CrossPoint Plus Matrix Switchers, cont’dSave or recall a preset View and adjust audio levelTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Plus Series Matrix SwitchersCrossPoint Plus Matrix Switchers Introduction CrossPoint Plus 128HVA FeaturesMatrix Input Status Introduction, cont’dAudio gain and attenuation Any input to any or all outputs Two CrossPoint Plus Matrix Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Power connectionAudio input and output connections HVA models only Video input and output connectionsRS-232/422 connection Installation, cont’dRear panel view, CrossPoint Plus 84HV Additional rear panel views11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Definitions Front Panel Controls and IndicatorsCrossPoint Plus Matrix Switchers Operation Operationeration, cont’dControl buttons and LEDs Input buttons, output buttons, and LEDsFront panel I/O label windows Operation, cont’dControls Grouping PowerFront Panel Operations Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step d Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presetsExample 7 Recall a preset Example 6 Save a presetExample 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockoutGeneral checks TroubleshootingSystem reset to factory defaults Rear Panel ControlsWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets Worksheet example 2 Drawing ties Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetOperation, cont’d Four Programmer’ser’sGuide,Guidecont’d Host-to-Switcher InstructionsSwitcher-Initiated Messages CrossPoint Plus Matrix Switchers Programmer’s GuideUsing the Command/Response Table Switcher Error ResponsesProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five MatrixSoftware,cont’d Matrix Switchers Control ProgramInstalling the software Using the softwareWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’dAudio output audio models only Audio audio models onlyAudio input audio models only Extron Part Specifications, cont’dPart Numbers CrossPoint Plus part numbersCables Optional accessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesAppendixBB ReferenceInformation,co t’d Hardware UpgradesOpening the switcher CrossPoint Plus Matrix Switchers Reference InformationFigure B-2 Removing the front cover Swapping the serial ports Closing the switcherReference Information, cont’d Figure B-4 Key and pin 1 mark Installing a firmware updateButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA