Extron electronic HVA, 1616 HV manual Button Labels

Page 68

Reference Information, cont’d

10.Reinstall the switcher’s front panel and cover. See Closing the switcher on page B-4.

If you choose to check for proper operation before putting the cover back on, ensure that tools and hands are outside the switcher and then perform step 11. After recognizing the new IC, the switcher should power up normally. Unplug the AC power cord, and reinstall the switcher.

11.Reinitialize the switcher to recognize the new IC as follows: a. Connect the power cord to the AC power source.

b. Press and hold the Enter button while you connect the power cord to the switcher.

c. Observe that the Input, Output, Preset, View, and Esc LEDs all flash.

d. Release the Enter button.

12. Ensure that the switcher is working properly.

13.If the switcher was removed from a rack, remove its power cord, reattach the switcher to the rack, and reconnect the power cord.

14. Reconnect the input and output cables.

Replacing the AC fuse (CrossPoint Plus 84, 88, 124, and 128 only)

The AC fuse on the power supply board is a user-replaceable component of the CrossPoint Plus 84, 88, 124, and 128. To replace the AC fuse, do the following:

1.Follow the instructions in Opening the CrossPoint Plus 84, 88, 124, and 128 on page B-2 to remove the top cover.

2.Locate the fuse on the power supply board (see figure B-1), and remove it from its retaining clips.

3.If test equipment is available, you can check the fuse.

4.Place a new 2A/250V fast-blow fuse in the retaining clips.

5.Reinstall the switcher’s cover. See Closing the switcher on page B-4.

If you choose to check the switcher for proper operation before putting the cover back on, ensure that tools and hands are outside the switcher, and then connect the power cord to the unit and to an AC source. The switcher should power up normally. Unplug the AC power cord, and reinstall the switcher.

6.Attach the power cord to the switcher and to the AC power source. Make sure the switcher is working properly.

7.If the switcher was removed from a rack, remove its power cord, reattach the switcher to the rack, and reconnect the power cord.

8.

Reconnect the input and output cables.

Button Labels

Figure B-5 provides blanks of a 16-button strip of button labels. Feel free to photocopy them or cut them out of the manual, write button information in each button area as desired, and put them in the switcher’s label window. For 8-button strips and 12-button strips, use scissors to trim the blank to the appropriate length.

B-6 CrossPoint Plus Matrix Switchers • Reference Information

Page 67 Page 69
Image 68
Page 67 Page 69
Contents CrossPoint Plus Matrix Switchers CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVASafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers Quick Start CrossPoint Plus Matrix Switchers, cont’d Save or recall a presetView and adjust audio level Create a tieTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Plus Series Matrix SwitchersCrossPoint Plus Matrix Switchers Introduction Features CrossPoint Plus 128HVAIntroduction, cont’d Matrix Input StatusAudio gain and attenuation Any input to any or all outputs Two Installationstallation, cont’d Rack Mounting the SwitcherPower connection CrossPoint Plus Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint Plus 84HV11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Front Panel Controls and Indicators CrossPoint Plus Matrix Switchers OperationOperationeration, cont’d DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsFront panel I/O label windows Operation, cont’dControls Grouping PowerFront Panel Operations Creating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step d Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets 13 Example 5, step d Muting and unmuting outputsExample 6 Save a preset Example 7 Recall a presetViewing and adjusting the input audio level HVA models only Example 8 View and adjust an audio level17 +8dB displayed, CrossPoint Plus 168 Executive mode front panel security lockout 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint PlusTroubleshooting System reset to factory defaultsRear Panel Controls General checksWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets Worksheet example 3 Test configuration Worksheet example 2 Drawing tiesMatrix Switchers Configuration Worksheet Preset #Operation, cont’d Four Host-to-Switcher Instructions Switcher-Initiated MessagesCrossPoint Plus Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Matrix Switchers Control Program Installing the softwareUsing the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Plus Matrix Switchers SpecificationsAudio output audio models only Audio audio models onlyAudio input audio models only Specifications, cont’d Part NumbersCrossPoint Plus part numbers Extron PartOptional accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableAppendixBB Hardware Upgrades Opening the switcherCrossPoint Plus Matrix Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Removing the front cover Swapping the serial ports Closing the switcherReference Information, cont’d Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents