Extron electronic HVA manual ReferenceInformation,co t’d, Hardware Upgrades, Opening the switcher

Page 64

ReferenceInformation,co t’d

Hardware Upgrades

This appendix contains procedures for performing hardware maintenance procedures such as swapping the RS-232 and RS-422 ports, installing a new firmware update, and replacing the fuse.

Opening the switcher

Before you can perform any of the hardware upgrade procedures, you must open the switcher. The interior of the CrossPoint Plus 84, 88, 124, and 188 switchers is accessed by removing the top cover. The interior of the CrossPoint Plus 168 and 1616 is accessed by removing the front cover.

Opening the CrossPoint Plus 84, 88, 124, and 128

To open the CrossPoint Plus 84, 88, 124, or 128 switcher, do the following:

1.Disconnect the power cord from the switcher.

2.If the switcher is rack mounted, remove the switcher from the rack and place it on a clean workspace.

3.Remove the eight screws that secure the switcher’s top cover as shown in figure B-1.

NOTE If you are installing a firmware update, also remove two screws in this location on the bottom cover.

Fuse

Power supply

Video board

Front panel board

Figure B-1 — Removing the top cover

CAUTION

Do not touch the components inside the switcher without being electrically grounded. Electrostatic discharge (ESD) can damage ICs, even if you cannot feel, see, or hear it.

4.Lift the top cover straight up as shown in figure B-1. Lift the cover evenly to clear the grooves at the edge of the rear panel.

B-2 CrossPoint Plus Matrix Switchers • Reference Information

Image 64

Contents CrossPoint Plus Matrix Switchers CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVASafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers Quick Start CrossPoint Plus Matrix Switchers, cont’d Save or recall a presetView and adjust audio level Create a tieTable of Contents Table of Contents, cont’d One CrossPoint Plus Matrix Switchers Introduction About the CrossPoint Plus Series Matrix SwitchersIntroductiontroduction, cont’d Features CrossPoint Plus 128HVAIntroduction, cont’d Matrix Input StatusAudio gain and attenuation Any input to any or all outputs Two Installationstallation, cont’d Rack Mounting the SwitcherPower connection CrossPoint Plus Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint Plus 84HV11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Front Panel Controls and Indicators CrossPoint Plus Matrix Switchers OperationOperationeration, cont’d DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsControls Operation, cont’dFront panel I/O label windows Front Panel Operations PowerGrouping Creating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step d Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets 13 Example 5, step d Muting and unmuting outputsExample 6 Save a preset Example 7 Recall a presetViewing and adjusting the input audio level HVA models only Example 8 View and adjust an audio level17 +8dB displayed, CrossPoint Plus 168 Executive mode front panel security lockout 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint PlusTroubleshooting System reset to factory defaultsRear Panel Controls General checksWorksheets Plasma display S-video problemWorksheet example 1 Entering system equipment Worksheet example 3 Test configuration Worksheet example 2 Drawing tiesMatrix Switchers Configuration Worksheet Preset #Operation, cont’d Four Host-to-Switcher Instructions Switcher-Initiated MessagesCrossPoint Plus Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand Ascii Command Response Additional description Command/Response TableProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Matrix Switchers Control Program Installing the softwareUsing the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing the help system Using emulation modeButton-Label Generator Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Plus Matrix Switchers SpecificationsAudio input audio models only Audio audio models onlyAudio output audio models only Specifications, cont’d Part NumbersCrossPoint Plus part numbers Extron PartOptional accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableAppendixBB Hardware Upgrades Opening the switcherCrossPoint Plus Matrix Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Removing the front cover Reference Information, cont’d Closing the switcherSwapping the serial ports Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA