Extron electronic HVA, 1616 HV manual Rgbhv Audio View

Page 30

Operation, cont’d

Example 4: View video and audio, audio-only, and video-only ties

See figure 3-9, figure 3-10, figure 3-11, and figure 3-12 and the following steps for an example of viewing the video and audio, audio-only, and video-only ties in the current configuration.

Example 4 shows the process of viewing the current configuration after the steps in Examples 1, 2, and 3 have been performed.

			LED key:			= off,		= on,				Press	Press
					F = flash once						Press		C
											Press		C
					INPUTS						B	RGBHV	AUDIO
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12

VIEW

CONTROL

I/O

1

2

3

4

5

6

7

8

ENTER PRESET VIEW ESC

RGBHV AUDIO

OUTPUTS

C	Press	F
	Press

2

5

6

7

A

ESC

Figure 3-9 — Example 4: Viewing the current configuration, no input selected

APress and release the Esc button. The Esc LED flashes once.

BPress and release the View button to enter view-only mode. The View LED lights. With no input LED selected, all output LEDs that have no established ties light.

CTo select both video and audio for viewing, if necessary, press and release the RGBHV and Audio buttons until the RGBHV LED and Audio LED light. With no input LED selected, all output LEDs that have no established ties light.

DPress and release the input 5 button (figure 3-10). The input 5 LED lights.

If ties are established for input 5, all output LEDs toggle; outputs with no ties turn off and the LEDs associated with all outputs tied to input 5 (audio, video, or audio and video ties) light. If no ties are established for input 5, all output LEDs turn off.

If audio is broken away, the Audio LED blinks.

				5
			Press					LED key:			= off,	= on, B = blinking
			D
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12

B D

RGBHV AUDIO

CONTROL

I/O

1

2

3

4

5

6

7

8

OUTPUTS

ENTER PRESET VIEW ESC

RGBHV AUDIO

D

1

3

4

8

Figure 3-10 — Example 4, step d: Viewing the current configuration, video and audio

3-10 CrossPoint Plus Matrix Switchers • Operation

Image 30

Contents CrossPoint Plus Matrix Switchers CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVASicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers View and adjust audio level Quick Start CrossPoint Plus Matrix Switchers, cont’dSave or recall a preset Create a tieTable of Contents Table of Contents, cont’d One About the CrossPoint Plus Series Matrix Switchers CrossPoint Plus Matrix Switchers IntroductionIntroductiontroduction, cont’d Features CrossPoint Plus 128HVAIntroduction, cont’d Matrix Input StatusAudio gain and attenuation Any input to any or all outputs Two Power connection Installationstallation, cont’dRack Mounting the Switcher CrossPoint Plus Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint Plus 84HV11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint Plus Matrix Switchers Operation DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsOperation, cont’d ControlsFront panel I/O label windows Power Front Panel OperationsGrouping Creating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step d Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets 13 Example 5, step d Muting and unmuting outputsExample 6 Save a preset Example 7 Recall a presetViewing and adjusting the input audio level HVA models only Example 8 View and adjust an audio level17 +8dB displayed, CrossPoint Plus 168 Executive mode front panel security lockout 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint PlusRear Panel Controls TroubleshootingSystem reset to factory defaults General checksPlasma display S-video problem WorksheetsWorksheet example 1 Entering system equipment Worksheet example 3 Test configuration Worksheet example 2 Drawing tiesMatrix Switchers Configuration Worksheet Preset #Operation, cont’d Four CrossPoint Plus Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Using the software Matrix Switchers Control ProgramInstalling the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Plus Matrix Switchers SpecificationsAudio audio models only Audio input audio models onlyAudio output audio models only CrossPoint Plus part numbers Specifications, cont’dPart Numbers Extron PartOptional accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableAppendixBB CrossPoint Plus Matrix Switchers Reference Information Hardware UpgradesOpening the switcher ReferenceInformation,co t’dFigure B-2 Removing the front cover Closing the switcher Reference Information, cont’dSwapping the serial ports Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA