Extron electronic 1616 HV, HVA manual Muting and unmuting video and/or audio

Page 31

A set of ties can also be viewed by selecting a tied output. To demonstrate this, note the number of a lit output LED and press and release the output button for an unlit (untied) output LED. Observe that all of the untied outputs light. Then press the output button for the output LED noted previously and observe that the selected output LED, the tied input LED (input 5), and the output LEDs light for all of the outputs that are tied to the input.

EPress and release the RGBHV button to toggle the Video LED off (figure 3-11). If audio is broken away, the Audio LED stops blinking and lights steadily.

If audio ties are established for input 5, the output LEDs for all audio outputs tied to input 5 light. If no ties are established for input 5, all output LEDs turn off.

								LED key:			= off,	= on
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
1	2	3	4	5	6	7	8
			OUTPUTS

E

38

	Press
	E
	RGBHV AUDIO
CONTROL	I/O
ENTER PRESET VIEW	ESC RGBHV AUDIO

Figure 3-11 — Example 4, step e: Viewing the current configuration, audio-only

FPress and release the RGBHV and Audio buttons to toggle the Video LED on and the Audio LED off (figure 3-12).

								LED key:			= off,	= on
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
1	2	3	4	5	6	7	8
			OUTPUTS
									F
1		3	4				8

	Press
	F
	RGBHV AUDIO
CONTROL	I/O
ENTER PRESET VIEW	ESC RGBHV AUDIO

Figure 3-12 — Example 4, step f: Viewing the current configuration, video-only

If video ties are established for input 5, the output LEDs for all video outputs tied to input 5 light. If no ties are established for input 5, all output LEDs turn off.

Muting and unmuting video and/or audio

Individual outputs can be muted or unmuted by doing the following:

1.	Press the Esc button to clear any input LEDs, output LEDs, or control LEDs
	that may be on.
2.	Press and release the View button.
3.	Select video, audio, or both to mute or unmute by pressing the RGBHV and/
	or Audio buttons.

CrossPoint Plus Matrix Switchers • Operation 3-11

Image 31

Contents CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQuick Start CrossPoint Plus Matrix Switchers Create a tie Quick Start CrossPoint Plus Matrix Switchers, cont’dSave or recall a preset View and adjust audio levelTable of Contents Table of Contents, cont’d One CrossPoint Plus Matrix Switchers Introduction About the CrossPoint Plus Series Matrix SwitchersIntroductiontroduction, cont’d CrossPoint Plus 128HVA FeaturesMatrix Input Status Introduction, cont’dAudio gain and attenuation Any input to any or all outputs Two CrossPoint Plus Matrix Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Power connectionAudio input and output connections HVA models only Video input and output connectionsRS-232/422 connection Installation, cont’dRear panel view, CrossPoint Plus 84HV Additional rear panel views11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Definitions Front Panel Controls and IndicatorsCrossPoint Plus Matrix Switchers Operation Operationeration, cont’dControl buttons and LEDs Input buttons, output buttons, and LEDsControls Operation, cont’dFront panel I/O label windows Front Panel Operations PowerGrouping Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step d Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presetsExample 7 Recall a preset Example 6 Save a presetExample 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockoutGeneral checks TroubleshootingSystem reset to factory defaults Rear Panel ControlsWorksheets Plasma display S-video problemWorksheet example 1 Entering system equipment Worksheet example 2 Drawing ties Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetOperation, cont’d Four Programmer’ser’sGuide,Guidecont’d Host-to-Switcher InstructionsSwitcher-Initiated Messages CrossPoint Plus Matrix Switchers Programmer’s GuideUsing the Command/Response Table Switcher Error ResponsesCommand Ascii Command Response Additional description Command/Response TableProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five MatrixSoftware,cont’d Matrix Switchers Control ProgramInstalling the software Using the softwareWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing the help system Using emulation modeButton-Label Generator Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’dAudio input audio models only Audio audio models onlyAudio output audio models only Extron Part Specifications, cont’dPart Numbers CrossPoint Plus part numbersCables Optional accessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesAppendixBB ReferenceInformation,co t’d Hardware UpgradesOpening the switcher CrossPoint Plus Matrix Switchers Reference InformationFigure B-2 Removing the front cover Reference Information, cont’d Closing the switcherSwapping the serial ports Figure B-4 Key and pin 1 mark Installing a firmware updateButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA