Extron electronic HVA, 1616 HV manual Example 6 Save a preset, Example 7 Recall a preset

Page 34

Operation, cont’d

Example 6: Save a preset

Refer to figure 3-14 and the following steps for an example of saving the current configuration as a preset.

1
F	LED key: = off,	= on, B = blinking,

F= flash once

C

					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
1	2	3	4	5	6	7	8
			OUTPUTS

C

BF

B

PRESET ESC

CONTROL

ENTER PRESET VIEW ESC

A

I/O

RGBHV AUDIO

Figure 3-14 — Example 6: Saving the current configuration as preset 1

APress and release the Esc button. The Esc LED flashes once.

BPress and hold the Preset button for approximately 2 seconds until the Preset LED begins to blink, then release the Preset button.

CPress and release the input 1 button. The input 1 LED flashes once. The Preset LED turns off.

Example 7: Recall a preset

Refer to figure 3-15 and the following steps for an example of recalling a preset to become the current configuration.

1
F						LED key:			= off,		= on
Press									F = flash once
		C							F = flash once
		C
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
1	2	3	4	5	6	7	8
			OUTPUTS

C

Press	F	Press
B		A
PRESET	ESC
CONTROL		I/O
ENTER PRESET VIEW	ESC	RGBHV AUDIO

Figure 3-15 — Example 7: Recalling preset 1

APress and release the Esc button. The Esc LED flashes once.

BPress and release the Preset button. The Preset LED lights.

CPress and release the input 1 button. The input 1 LED flashes once. The Preset LED turns off. The configuration stored in memory location 1 is now the current configuration and can be viewed in the view-only mode (Example 4).

3-14 CrossPoint Plus Matrix Switchers • Operation

Image 34

Contents CrossPoint Plus Matrix Switchers CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVASicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers View and adjust audio level Quick Start CrossPoint Plus Matrix Switchers, cont’dSave or recall a preset Create a tieTable of Contents Table of Contents, cont’d One CrossPoint Plus Matrix Switchers Introduction About the CrossPoint Plus Series Matrix SwitchersIntroductiontroduction, cont’d Features CrossPoint Plus 128HVAIntroduction, cont’d Matrix Input StatusAudio gain and attenuation Any input to any or all outputs Two Power connection Installationstallation, cont’dRack Mounting the Switcher CrossPoint Plus Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint Plus 84HV11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint Plus Matrix Switchers Operation DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsControls Operation, cont’dFront panel I/O label windows Front Panel Operations PowerGrouping Creating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step d Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets 13 Example 5, step d Muting and unmuting outputsExample 6 Save a preset Example 7 Recall a presetViewing and adjusting the input audio level HVA models only Example 8 View and adjust an audio level17 +8dB displayed, CrossPoint Plus 168 Executive mode front panel security lockout 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint PlusRear Panel Controls TroubleshootingSystem reset to factory defaults General checksWorksheets Plasma display S-video problemWorksheet example 1 Entering system equipment Worksheet example 3 Test configuration Worksheet example 2 Drawing tiesMatrix Switchers Configuration Worksheet Preset #Operation, cont’d Four CrossPoint Plus Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand Ascii Command Response Additional description Command/Response TableProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Using the software Matrix Switchers Control ProgramInstalling the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing the help system Using emulation modeButton-Label Generator Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Plus Matrix Switchers SpecificationsAudio input audio models only Audio audio models onlyAudio output audio models only CrossPoint Plus part numbers Specifications, cont’dPart Numbers Extron PartOptional accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableAppendixBB CrossPoint Plus Matrix Switchers Reference Information Hardware UpgradesOpening the switcher ReferenceInformation,co t’dFigure B-2 Removing the front cover Reference Information, cont’d Closing the switcherSwapping the serial ports Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA