Extron electronic HVA, 1616 HV manual Pre-cut cables, Extron Part BNC-4 Mini HR Cable

Page 62

Specifications, cont’d

Pre-cut cables

BNC-4 Mini HR cable is used for RGBS cable runs, and BNC-5 Mini HR cable is used for RGBHV cable runs. Either type can also be used for composite video, S-video, or RGsB. All Extron BNC cables have male connectors on both ends. A plenum version of the BNC-5 Mini HR cable is also available.

Extron Part	Part #
BNC-4 Mini HR Cable
BNC-4-25’ MHR (25 feet/7.5 meters)	26-210-04
BNC-4-50’ MHR (50 feet/15.0 meters)	26-210-05
BNC-4-75’ MHR (75 feet/23.0 meters)	26-210-06
BNC-4-100’ MHR (100 feet/30.0 meters)	26-210-07
BNC-4-150’ MHR (150 feet/45.0 meters)	26-210-08
BNC-4-200’ MHR (200 feet/60.0 meters)	26-210-09
BNC-4-250’ MHR (250 feet/75.0 meters)	26-210-54
BNC-4-300’ MHR (300 feet/90.0 meters)	26-210-53

BNC-5 Mini HR Cable
BNC-5-25’ MHR (25 feet/7.5 meters)	26-260-03
BNC-5-50’ MHR (50 feet/15.0 meters)	26-260-04
BNC-5-75’ MHR (75 feet/23.0 meters)	26-260-16
BNC-5-100’ MHR (100 feet/30.0 meters)	26-260-05
BNC-5-150’ MHR (150 feet/45.0 meters)	26-260-12
BNC-5-200’ MHR (200 feet/60.0 meters)	26-260-06
BNC-5-250’ MHR (250 feet/75.0 meters)	26-260-18
BNC-5-300’ MHR (300 feet/90.0 meters)	26-260-14

Bulk cable in lengths up to 5000' (1524 meter) rolls is available with or without connectors.

A-6 CrossPoint Plus Matrix Switchers • Specifications

Image 62

Contents CrossPoint Plus Matrix Switchers CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVASicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers View and adjust audio level Quick Start CrossPoint Plus Matrix Switchers, cont’dSave or recall a preset Create a tieTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Plus Series Matrix SwitchersCrossPoint Plus Matrix Switchers Introduction Features CrossPoint Plus 128HVAIntroduction, cont’d Matrix Input StatusAudio gain and attenuation Any input to any or all outputs Two Power connection Installationstallation, cont’dRack Mounting the Switcher CrossPoint Plus Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint Plus 84HV11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint Plus Matrix Switchers Operation DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsFront panel I/O label windows Operation, cont’dControls Grouping PowerFront Panel Operations Creating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step d Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets 13 Example 5, step d Muting and unmuting outputsExample 6 Save a preset Example 7 Recall a presetViewing and adjusting the input audio level HVA models only Example 8 View and adjust an audio level17 +8dB displayed, CrossPoint Plus 168 Executive mode front panel security lockout 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint PlusRear Panel Controls TroubleshootingSystem reset to factory defaults General checksWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets Worksheet example 3 Test configuration Worksheet example 2 Drawing tiesMatrix Switchers Configuration Worksheet Preset #Operation, cont’d Four CrossPoint Plus Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Using the software Matrix Switchers Control ProgramInstalling the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Plus Matrix Switchers SpecificationsAudio output audio models only Audio audio models onlyAudio input audio models only CrossPoint Plus part numbers Specifications, cont’dPart Numbers Extron PartOptional accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableAppendixBB CrossPoint Plus Matrix Switchers Reference Information Hardware UpgradesOpening the switcher ReferenceInformation,co t’dFigure B-2 Removing the front cover Swapping the serial ports Closing the switcherReference Information, cont’d Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA