Extron electronic 1616 HV, HVA manual Quick Start CrossPoint Plus Matrix Switchers

Page 3

Quick Start — CrossPoint Plus Matrix Switchers

Installation

Step 1

Mount the switcher in a rack.

Step 2

Turn off power to the input and output devices, and remove the power cords from them.

Step 3

Cable the switcher for RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video input and output (3). See page 2-3 in this manual for details.

Step 4

Cable the switcher for stereo audio input (HVA models). Each input has a 3.5 mm, 5-pole captive screw connector for balanced or unbalanced stereo audio input (4). Connectors are included with each switcher, but you must supply the audio cable. High impedance is generally over 800 ohms.

Step 5

Cable the switcher for stereo audio output (HVA models). Each output has a 3.5 mm, 5-pole captive screw connector that outputs the selected unamplified, line level audio. Connect an audio device, such as an audio amplifier or powered speakers (5).

3

5

Tip	AUDIO
Tip	AUDIO
See caution
Sleeve
See caution
Unbalanced Output
Tip	AUDIO
Tip	AUDIO
Ring
Sleeve (s)
Ring

Balanced Output

6

4

Tip

Sleeve

Tip

Sleeve

Unbalanced Input

(high impedance)

Tip

Ring

Sleeve (s)

Tip

Ring

Balanced Input

(high impedance)

600 ohms

Tip

Ring

Sleeve (s)

Tip

Ring

600 ohms

Balanced Input

(600 ohms)

CAUTION Connect the sleeve to ground. Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

Step 6

If desired, connect a control system or computer to the Remote RS-232/RS-422 port (6).

Step 7

5	1	1	5
9	6	6	9
Female		Male

Plug the switcher, input devices, and output devices into a grounded AC source, and turn on the input and output devices.

Definitions

The following terms are used throughout this manual:

Tie — An input-to-output connection.

Pin RS-232 Function

1	—	Not used
2	TX	Transmit data
3	RX	Receive data

4— Not used

5Gnd Signal ground

6— Not used

7— Not used

8— Not used

9— Not used

RS-422	Function
TX-	Transmit data (-)
TX+	Transmit data (+)
RX+	Receive data (+)
RX-	Receive data (-)
Gnd	Signal ground
—	Not used
—	Not used
—	Not used
—	Not used

Set of ties — An input tied to two or more outputs. (An output can never be tied to multiple inputs.)

Configuration — One or more ties or sets of ties.

Current configuration — The currently active configuration (also called configuration 0).

Preset — A configuration that has been stored. One preset can be assigned to each input button. When a preset is retrieved from memory, it becomes the current configuration.

Image 3

Contents CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQuick Start CrossPoint Plus Matrix Switchers Create a tie Quick Start CrossPoint Plus Matrix Switchers, cont’dSave or recall a preset View and adjust audio levelTable of Contents Table of Contents, cont’d One About the CrossPoint Plus Series Matrix Switchers CrossPoint Plus Matrix Switchers IntroductionIntroductiontroduction, cont’d CrossPoint Plus 128HVA FeaturesMatrix Input Status Introduction, cont’dAudio gain and attenuation Any input to any or all outputs Two CrossPoint Plus Matrix Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Power connectionAudio input and output connections HVA models only Video input and output connectionsRS-232/422 connection Installation, cont’dRear panel view, CrossPoint Plus 84HV Additional rear panel views11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Definitions Front Panel Controls and IndicatorsCrossPoint Plus Matrix Switchers Operation Operationeration, cont’dControl buttons and LEDs Input buttons, output buttons, and LEDsOperation, cont’d ControlsFront panel I/O label windows Power Front Panel OperationsGrouping Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step d Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presetsExample 7 Recall a preset Example 6 Save a presetExample 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockoutGeneral checks TroubleshootingSystem reset to factory defaults Rear Panel ControlsPlasma display S-video problem WorksheetsWorksheet example 1 Entering system equipment Worksheet example 2 Drawing ties Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetOperation, cont’d Four Programmer’ser’sGuide,Guidecont’d Host-to-Switcher InstructionsSwitcher-Initiated Messages CrossPoint Plus Matrix Switchers Programmer’s GuideUsing the Command/Response Table Switcher Error ResponsesCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five MatrixSoftware,cont’d Matrix Switchers Control ProgramInstalling the software Using the softwareWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’dAudio audio models only Audio input audio models onlyAudio output audio models only Extron Part Specifications, cont’dPart Numbers CrossPoint Plus part numbersCables Optional accessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesAppendixBB ReferenceInformation,co t’d Hardware UpgradesOpening the switcher CrossPoint Plus Matrix Switchers Reference InformationFigure B-2 Removing the front cover Closing the switcher Reference Information, cont’dSwapping the serial ports Figure B-4 Key and pin 1 mark Installing a firmware updateButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA