Extron electronic 1616 HV, HVA manual Table of Contents

Page 5

Table of Contents

Chapter 1 • Introduction	1-1
About the CrossPoint Plus Series Matrix Switchers	1-2
Features	1-3
Chapter 2 • Installation	2-1
Rack Mounting the Switcher	2-2
Cabling and Rear Panel Views	2-2
Power connection	2-2
Video input and output connections	2-3
Audio input and output connections (HVA models only)	2-3
RS-232/422 connection	2-4
Additional rear panel views	2-5
Chapter 3 • Operation	3-1
Front Panel Controls and Indicators	3-2
Definitions	3-2
Input buttons, output buttons, and LEDs	3-3
Control buttons and LEDs	3-3
I/O controls	3-4
Front panel I/O label windows	3-4
Front Panel Operations	3-5
Power	3-5
I/O grouping	3-5
Creating a configuration	3-6
Example 1: Create a set of video and audio ties	3-7
Example 2: Add a tie to a set of video and audio ties	3-7
Example 3: Remove a tie from a set of video and audio ties	3-8
Viewing a configuration	3-9
Example 4: View video and audio, audio only, and video only ties	3-10
Muting and unmuting video and/or audio	3-11
Example 5: Muting and unmuting an output	3-12
Using presets	3-13
Example 6: Save a preset	3-14
Example 7: Recalle a preset	3-14
Viewing and adjusting the input audio level (HVA models only)	3-15
Example 8: View and adjust an audio level	3-15
Executive mode (front panel security lockout)	3-17
System reset to factory defaults	3-18
Rear Panel Controls	3-18
Troubleshooting	3-18
General checks	3-18
Plasma display S-video problem	3-19
Worksheets	3-19
Worksheet example 1: Entering system equipment	3-19

CrossPoint Plus Matrix Switchers • Table of Contents

i

Image 5

Contents CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers Save or recall a preset Quick Start CrossPoint Plus Matrix Switchers, cont’dView and adjust audio level Create a tieTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Plus Series Matrix SwitchersCrossPoint Plus Matrix Switchers Introduction CrossPoint Plus 128HVA FeaturesMatrix Input Status Introduction, cont’dAudio gain and attenuation Any input to any or all outputs Two Rack Mounting the Switcher Installationstallation, cont’dPower connection CrossPoint Plus Matrix Switchers InstallationAudio input and output connections HVA models only Video input and output connectionsRS-232/422 connection Installation, cont’dRear panel view, CrossPoint Plus 84HV Additional rear panel views11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three CrossPoint Plus Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d DefinitionsControl buttons and LEDs Input buttons, output buttons, and LEDsFront panel I/O label windows Operation, cont’dControls Grouping PowerFront Panel Operations Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step d Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presetsExample 7 Recall a preset Example 6 Save a presetExample 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockoutSystem reset to factory defaults TroubleshootingRear Panel Controls General checksWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets Worksheet example 2 Drawing ties Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetOperation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsCrossPoint Plus Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dUsing the Command/Response Table Switcher Error ResponsesProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Installing the software Matrix Switchers Control ProgramUsing the software MatrixSoftware,cont’dWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’dAudio output audio models only Audio audio models onlyAudio input audio models only Part Numbers Specifications, cont’dCrossPoint Plus part numbers Extron PartCables Optional accessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesAppendixBB Opening the switcher Hardware UpgradesCrossPoint Plus Matrix Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Removing the front cover Swapping the serial ports Closing the switcherReference Information, cont’d Figure B-4 Key and pin 1 mark Installing a firmware updateButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA