Extron electronic 1616 HV, HVA manual Figure B-2 Removing the front cover

Page 65

Self-latching receptacle

Connector

Ribbon cable

Press the two receptacle tabs on the top cable outward as shown at the left, and pull back gently on the cable connector to remove it

from the receptacle. Lay the front panel down in front

of the switcher.

Self-latching receptacle

Opening the CrossPoint Plus 168 and 1616

To open the CrossPoint Plus 168 or 1616 switcher, do the following: 1. Disconnect the power cord from the switcher.

Ribbon cable

Connector

5.If you are updating the firmware, remove the two screws at the front edge of

the bottom cover, press the two receptacle tabs on the top cable outward as shown at the left, and pull back gently on the cable connector to remove it from the receptacle. Lay the front panel down in front of the switcher.

CAUTION

Do not strain the three internal cables connected to the front panel. Too much strain can be damage the cables.

CAUTION

Do not touch the components inside the switcher without being electrically grounded. Electrostatic discharge (ESD) can damage ICs, even if you cannot feel, see, or hear it.

2.Remove the ten screws that secure the switcher’s front cover as shown in figure B-2. Carefully tilt the front panel away from the main body of the switcher.

Figure B-2 — Removing the front cover

3.

CrossPoint Plus Matrix Switchers • Reference Information

B-3

Image 65

Contents CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers Save or recall a preset Quick Start CrossPoint Plus Matrix Switchers, cont’dView and adjust audio level Create a tieTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Plus Series Matrix SwitchersCrossPoint Plus Matrix Switchers Introduction CrossPoint Plus 128HVA FeaturesMatrix Input Status Introduction, cont’dAudio gain and attenuation Any input to any or all outputs Two Rack Mounting the Switcher Installationstallation, cont’dPower connection CrossPoint Plus Matrix Switchers InstallationAudio input and output connections HVA models only Video input and output connectionsRS-232/422 connection Installation, cont’dRear panel view, CrossPoint Plus 84HV Additional rear panel views11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three CrossPoint Plus Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d DefinitionsControl buttons and LEDs Input buttons, output buttons, and LEDsFront panel I/O label windows Operation, cont’dControls Grouping PowerFront Panel Operations Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step d Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presetsExample 7 Recall a preset Example 6 Save a presetExample 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockoutSystem reset to factory defaults TroubleshootingRear Panel Controls General checksWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets Worksheet example 2 Drawing ties Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetOperation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsCrossPoint Plus Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dUsing the Command/Response Table Switcher Error ResponsesProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Installing the software Matrix Switchers Control ProgramUsing the software MatrixSoftware,cont’dWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’dAudio output audio models only Audio audio models onlyAudio input audio models only Part Numbers Specifications, cont’dCrossPoint Plus part numbers Extron PartCables Optional accessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesAppendixBB Opening the switcher Hardware UpgradesCrossPoint Plus Matrix Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Removing the front cover Swapping the serial ports Closing the switcherReference Information, cont’d Figure B-4 Key and pin 1 mark Installing a firmware updateButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA