Extron electronic HVA, 1616 HV manual Reference Information, cont’d, Closing the switcher

Page 66
Self-latching receptacle
Self-latching receptacle Ribbon cable
6. Reinstall the switcher’s cover. See Closing the switcher above.
5. To plug the cable into the desired receptacle, align the holes in the connector with the pins in the receptacle, and press evenly until the receptacle tabs lock into place.
To remove the cable from the current receptacle, press the two receptacle tabs
Ribbon cableoutward as shown at the left, and pull up gently on the cable
connector to remove it from the receptacle.
Connector

Reference Information, cont’d

Closing the switcher

1.

Reinstall any cables removed. To plug a self latching cable into the desired

 

Ribbon cable

receptacle, align the holes in the connector with the pins in the

 

 

 

receptacle, and press evenly until the receptacle tabs lock into

 

 

 

place.

Self-latching receptacle

 

2.

Place the top cover (CrossPoint Plus 84, 88, 124, and 128) and/or front cover

 

(all models) in place and replace all the screws removed in Opening the

 

switcher on page B-2.

Swapping the serial ports

The CrossPoint Plus switchers are factory configured for RS-232 use. If you want to use RS-422 and the switcher is configured for RS-232, or if you want to use RS-232 and the switcher is configured for RS-422, do the following:

1.Follow the appropriate instructions in Opening the Switcher on page B-2 to gain access to the interior of your switcher.

2.Locate the switcher’s front panel board (figure B-3).

Label includes

Key Extron part number &

Software version (Vx.xx)

 

Pin 1 (red stripe on ribbon cable )

19-708-01Vx.xx

 

 

J1 RS-422

Slots for removing IC

receptacle

J2 RS-232

with PLCC IC puller

receptacle

 

U7

 

Figure B-3 — CrossPoint Plus front panel board

CAUTION

Do not touch the components inside the switcher without being electrically grounded. Electrostatic discharge (ESD) can damage ICs, even if you cannot feel, see, or hear it.

3.On the side of the front panel board that faces the rear of the switcher, locate the RS-232 ribbon cable. The RS-422 ribbon cable receptacle, which is normally empty, is located to the left of the RS-232 ribbon cable receptacle.

4.

B-4 CrossPoint Plus Matrix Switchers • Reference Information

Page 65 Page 67
Image 66
Page 65 Page 67
Contents CrossPoint Plus Matrix Switchers CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVASicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers View and adjust audio level Quick Start CrossPoint Plus Matrix Switchers, cont’dSave or recall a preset Create a tieTable of Contents Table of Contents, cont’d One About the CrossPoint Plus Series Matrix Switchers CrossPoint Plus Matrix Switchers IntroductionIntroductiontroduction, cont’d Features CrossPoint Plus 128HVAIntroduction, cont’d Matrix Input StatusAudio gain and attenuation Any input to any or all outputs Two Power connection Installationstallation, cont’dRack Mounting the Switcher CrossPoint Plus Matrix Switchers InstallationVideo input and output connections Audio input and output connections HVA models onlyInstallation, cont’d RS-232/422 connectionAdditional rear panel views Rear panel view, CrossPoint Plus 84HV11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsCrossPoint Plus Matrix Switchers Operation DefinitionsInput buttons, output buttons, and LEDs Control buttons and LEDsOperation, cont’d ControlsFront panel I/O label windows Power Front Panel OperationsGrouping Creating a configuration Example 1 Create a set of video and audio ties Example 2 Add a tie to a set of video and audio tiesExample 2 Adding a video tie Example 3 Remove a tie from a set of video and audio tiesViewing a configuration Example 3, step d Removing an audio tieRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output Using presets 13 Example 5, step d Muting and unmuting outputsExample 6 Save a preset Example 7 Recall a presetViewing and adjusting the input audio level HVA models only Example 8 View and adjust an audio level17 +8dB displayed, CrossPoint Plus 168 Executive mode front panel security lockout 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint PlusRear Panel Controls TroubleshootingSystem reset to factory defaults General checksPlasma display S-video problem WorksheetsWorksheet example 1 Entering system equipment Worksheet example 3 Test configuration Worksheet example 2 Drawing tiesMatrix Switchers Configuration Worksheet Preset #Operation, cont’d Four CrossPoint Plus Matrix Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Using the software Matrix Switchers Control ProgramInstalling the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d CrossPoint Plus Matrix Switchers SpecificationsAudio audio models only Audio input audio models onlyAudio output audio models only CrossPoint Plus part numbers Specifications, cont’dPart Numbers Extron PartOptional accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableAppendixBB CrossPoint Plus Matrix Switchers Reference Information Hardware UpgradesOpening the switcher ReferenceInformation,co t’dFigure B-2 Removing the front cover Closing the switcher Reference Information, cont’dSwapping the serial ports Installing a firmware update Figure B-4 Key and pin 1 markButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents