Extron electronic 1616 HV, HVA Viewing a configuration, Example 3, step d Removing an audio tie

Page 29

5

LED key: = off, = on,

2= on for 2 seconds, then off

					INPUTS							AUDIO
1	2	3	4	5	6	7	8	9	10	11	12	AUDIO
											CONTROL	I/O
1	2	3	4	5	6	7	8				ENTER PRESET VIEW ESC	RGBHV AUDIO
			OUTPUTS
		3		Press			8				Press
											Press
				D
				D							E
			4								ENTER

Figure 3-8 — Example 3, step d: Removing an audio tie

EPress and release the Enter button. The input and output LEDs turn off. The current configuration is now defined as video input 5 tied to video output 1, output 3, output 4, and output 8; and audio input 5 tied to audio output 3 and output 8.

Viewing a configuration

The current configuration can be viewed using the front panel buttons. The view- only mode prevents inadvertent changes to the current configuration. View-only mode also provides a way to mute video and audio outputs (see Muting and unmuting video and/or audio in this chapter.

To view the current configuration, do the following:

1.	Press the Esc button to clear any input LEDs, output LEDs, or control LEDs
	that may be on.
2.	Press and release the View button.
3.	Select video, audio, or both to view by pressing the RGBHV and Audio
	buttons.
4.	Select the desired input or output(s) for which ties need to be viewed by
	pressing the input and output buttons.

1. To see all ties of the current configuration, press and release each input and output button, one at a time, with the RGBHV and Audio LEDs on.

2.If you select a grouped input or output in view-only mode, all of the input and output LEDs in the group flash for half a second and then the current configuration is displayed in the normal manner.

3.In view-only mode, you can view video and audio, video-only, or audio- only ties. Pressing and releasing the RGBHV and Audio buttons toggles each on and off.

4.If, when you view video and audio ties, the Audio LED blinks and the RGBHV LED is on after selecting an input or output, the LEDs indicate that the audio ties are not the same as the video ties for that input (audio breakaway is active). Toggle the RGBHV LED off by pressing and releasing the RGBHV button.

5.When you enter view-only mode, the output LEDs turn on for all outputs without ties. Likewise, when an output button is pushed for which there are no ties, the output LEDs turn on for all outputs without ties. The blinking Audio LED indicates audio breakaway for one or more of those outputs.

CrossPoint Plus Matrix Switchers • Operation

3-9

Image 29

Contents CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start CrossPoint Plus Matrix Switchers Save or recall a preset Quick Start CrossPoint Plus Matrix Switchers, cont’dView and adjust audio level Create a tieTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Plus Series Matrix SwitchersCrossPoint Plus Matrix Switchers Introduction CrossPoint Plus 128HVA FeaturesMatrix Input Status Introduction, cont’dAudio gain and attenuation Any input to any or all outputs Two Rack Mounting the Switcher Installationstallation, cont’dPower connection CrossPoint Plus Matrix Switchers InstallationAudio input and output connections HVA models only Video input and output connectionsRS-232/422 connection Installation, cont’dRear panel view, CrossPoint Plus 84HV Additional rear panel views11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three CrossPoint Plus Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d DefinitionsControl buttons and LEDs Input buttons, output buttons, and LEDsFront panel I/O label windows Operation, cont’dControls Grouping PowerFront Panel Operations Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio tiesExample 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tieExample 3, step d Removing an audio tie Viewing a configurationRgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presetsExample 7 Recall a preset Example 6 Save a presetExample 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockoutSystem reset to factory defaults TroubleshootingRear Panel Controls General checksWorksheet example 1 Entering system equipment Plasma display S-video problemWorksheets Worksheet example 2 Drawing ties Worksheet example 3 Test configurationPreset # Matrix Switchers Configuration WorksheetOperation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsCrossPoint Plus Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dUsing the Command/Response Table Switcher Error ResponsesProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Installing the software Matrix Switchers Control ProgramUsing the software MatrixSoftware,cont’dWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’dAudio output audio models only Audio audio models onlyAudio input audio models only Part Numbers Specifications, cont’dCrossPoint Plus part numbers Extron PartCables Optional accessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesAppendixBB Opening the switcher Hardware UpgradesCrossPoint Plus Matrix Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Removing the front cover Swapping the serial ports Closing the switcherReference Information, cont’d Figure B-4 Key and pin 1 mark Installing a firmware updateButton Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA